S11059-01WT_15 Datasheet, PDF (2/11 Pages) Hamamatsu Corporation – Color sensor

Color sensor
S11059-01WT
Absolute maximum ratings (Ta=25 °C)
Parameter
Symbol
Condition
Value
Unit
Supply voltage
Vdd
-0.3 to +6
V
Load current
Io
±10
mA
Power dissipation
P
100
mW
Operating temperature
Topr No dew condensation*¹
-40 to +85
°C
Storage temperature
Tstg No dew condensation*¹
-40 to +100
°C
Reflow soldering conditions*²
Tsol
Peak temperature 260 °C max., 3 times
-
*1: When there is a temperature difference between a product and the surrounding area in high humidity environment, dew
condensation may occur on the product surface. Dew condensation on the product may cause deterioration in characteristics and
reliability.
*2: Moisture absorption and reflow conditions: JEDEC J-STD-020D LEVEL2a
Note: Exceeding the absolute maximum ratings even momentarily may cause a drop in product quality. Always be sure to use the
product within the absolute maximum ratings.
Recommended operating conditions
Parameter
Symbol
Condition
Min.
Typ.
Max.
Unit
Supply voltage
Vdd
2.25
-
3.63
V
High level input voltage (SDA, SCL)*³ Vih
0.7Vdd
-
Vdd + 0.5
V
Low level input voltage (SDA, SCL)*³ Vil
-0.5
-
0.2Vdd
V
Bus capacitance (SDA, SCL)
Cbus
-
-
400
pF
*3: Set so that Vdd=Vbus. Normal operation cannot be guaranteed unless used with this condition.
Electrical and optical characteristics
Sensor section [Ta=25 °C, Vdd=3.3 V, A light source, unless otherwise noted (initial setting: low gain, integration time: 546 ms/ch)]
Parameter
Symbol
Condition
Min.
Typ.
Max.
Unit
Blue
400 to 540
Spectral response range*⁴
λ
Green
Red
455 to 630
575 to 660
nm
Infrared, more than 700 nm
785 to 885
Blue
-
460
-
Peak sensitivity wavelength
λp
Green
Red
-
530
-
-
615
-
nm
Infrared, more than 700 nm
-
855
-
Current consumption
Operating mode
Standby mode
Idd
Idds
E=0 lx (dark state),
excluding output current
30
75
150
0.1
1.0
3.0
μA
Dark count
Sd
E=0 lx (dark state)
-
-
5
counts
Gain ratio
rg High gain/Low gain
-
10
-
-
Sbl Blue
2.01
3.35
4.69
Sgl
Srl
Green
Red
Initial setting
4.57
5.69
7.61
9.48
10.66
13.28
Photo sensitivity Low gain
Sirl Infrared
Sbl Blue
-
2.51
1.66
3.35
-
4.19
counts/lx
Sgl
Srl
Green
Red
Initial setting*⁵
5.71
7.11
7.61
9.48
9.52
11.85
Sirl Infrared
-
1.66
-
Red/Blue sensi. ratio
Red/Green sensi. ratio Low gain
Blue/Green sensi. ratio
Srl/Sbl
Srl/Sgl
Sbl/Sgl
Initial setting
Same chip
2.12
2.83
3.54
0.93
1.25
1.56
-
0.33
0.44
0.55
Sbh Blue
19.0
31.7
44.4
Sgh Green Integration time
45.7
76.2
106.7
Srh Red 546 ms/ch
56.7
94.5
132.4
Photo sensitivity High gain
Sirh Infrared
Sbh Blue
-
23.8
15.3
31.7
-
39.7
counts/lx
Sgh Green Integration time
Srh Red 546 ms/ch*⁵
57.2
70.9
76.2
94.5
95.3
118.2
Sirh Infrared
-
15.3
-
Red/Blue sensi. ratio
Srh/Sbh
2.24
2.98
3.73
Red/Green sensi. ratio High gain
Srh/Sgh
Integration time 546 ms/ch
Same chip
0.93
1.24
1.55
-
Blue/Green sensi. ratio
Sbh/Sgh
0.31
0.42
0.52
Integration time
-
Integration time setting (Tint)
“00”
105
175
245
μs
*4: Relative sensitivity=more than 10%
*5: Integration time is measured and corrected. See "Compensation method for sensitivity variation". Integration time measurement
accuracy is 0.36%.
2