S11059-01WT Datasheet, PDF (2/9 Pages) Hamamatsu Corporation – I2C interface-compatible color sensor

Color sensor
S11059-01WT
Absolute maximum ratings (Ta=25 °C)
Parameter
Symbol
Value
Unit
Supply voltage
Vdd
-0.3 to +6
V
Load current
Io
±10
mA
Power dissipation
P
100
mW
Operating temperature
Topr
-40 to +85
°C
Storage temperature
Tstg
-40 to +100
°C
Reflow soldering conditions *¹
Tsol
Peak temperature 260 °C, 3 times
-
*1: Moisture absorption and reÀow conditions: JEDEC J-STD-020D LEVEL2a
Recommended operating conditions
Parameter
Symbol
Condition
Supply voltage
Vdd
I²C bus pull-up voltage
Vbus Rp *²=2.2 k:
High level input voltage
(SDA, SCL)
Vih
Vbust2.25 V, Vdd>2.75 V
Vbus<2.25 V, Vddd2.75 V
Low level input voltage
(SDA, SCL)
Vbust2.25 V, Vdd>2.75 V
Vil
Vbus<2.25 V, Vddd2.75 V
Bus capacitance (SDA, SCL)
Cbus
*2: Pull-up resistor value is determined by Cbus and Vbus.
Min.
Typ.
Max.
Unit
2.25
-
3.63
V
1.65
-
Vdd + 0.5
V
0.7Vbus
0.8Vbus
-
Vdd + 0.5
V
-
Vdd + 0.5
-0.5
-0.5
-
0.2Vbus
-
0.3Vbus
V
-
-
400
pF
Electrical and optical characteristics
Sensor section [Ta=25 °C, Vdd=3.3 V, A light source, unless otherwise noted (initial setting: low gain, integration time: 546 ms/ch)]
Parameter
Symbol
Condition
Min.
Typ.
Max.
Unit
Blue
400 to 540
Spectral response range *³
O
Green
Red
455 to 630
575 to 660
nm
Infrared, more than 700 nm
785 to 885
Blue
-
460
-
Peak sensitivity wavelength
Op
Green
Red
-
530
-
nm
-
615
-
Current consumption ^{Operating mode}
Standby mode
Dark count
Idd
Idds
Sd
Infrared, more than 700 nm
E=0 lx (dark state),
excluding output current
E=0 lx (dark state)
-
855
-
30
75
150
—A
0.1
1.0
3.0
-
-
5
counts
Gain ratio
rg High gain/Low gain
-
10
-
-
Sbl Blue
2.01
3.35
4.69
Sgl Green
Srl
Red ^{Initial setting}
4.57
5.69
7.61
9.48
10.66
13.28
Photo sensitivity Low gain
Sirl Infrared
Sbl Blue
-
2.51
1.66
3.35
-
4.19
counts/lx
Sgl
Green _{Initial setting *4}
Srl Red
5.71
7.11
7.61
9.48
9.52
11.85
Sirl Infrared
-
1.66
-
Red/Blue sensi. ratio
Red/Green sensi. ratio Low gain
Blue/Green sensi. ratio
Srl/Sbl
Srl/Sgl
Sbl/Sgl
Initial setting
Same chip
2.12
2.83
3.54
0.93
1.25
1.56
-
0.33
0.44
0.55
Sbh Blue
19.0
31.7
44.4
Sgh Green Integration time:
Srh Red 546 ms/ch
45.7
56.7
76.2
94.5
106.7
132.4
Photo sensitivity High gain
Sirh Infrared
Sbh Blue
-
23.8
15.3
31.7
-
39.7
counts/lx
Sgh Green Integration time:
Srh Red 546 ms/ch *⁴
57.2
70.9
76.2
94.5
95.3
118.2
Sirh Infrared
-
15.3
-
Red/Blue sensi. ratio
Red/Green sensi. ratio High gain
Blue/Green sensi. ratio
Srh/Sbh
Srh/Sgh
Integration time: 546 ms/ch
Same chip
Sbh/Sgh
2.24
2.98
3.73
0.93
1.24
1.55
-
0.31
0.42
0.52
*3: Relative sensitivity=more than 10%
*4: Integration time is measured and corrected. See "Compensation method for sensitivity variation". Integration time measurement
accuracy is 0.36%.
2