S7030 Datasheet, PDF (12/12 Pages) Hamamatsu Corporation – Back-thinned FFT-CCD

CCD area image sensors
S7030/S7031 series
Precaution for use (electrostatic countermeasures)
O Handle these sensors with bare hands or wearing cotton gloves. In addition, wear anti-static clothing or use a wrist band with an earth ring, in
order to prevent electrostatic damage due to electrical charges from friction.
O Avoid directly placing these sensors on a work-desk or work-bench that may carry an electrostatic charge.
O Provide ground lines or ground connection with the work-Àoor, work-desk and work-bench to allow static electricity to discharge.
O Ground the tools used to handle these sensors, such as tweezers and soldering irons.
It is not always necessary to provide all the electrostatic measures stated above. Implement these measures according to the amount of damage
that occurs.
Element cooling/heating temperature incline rate
When cooling the CCD by an externally attached cooler, set the cooler operation so that the temperature gradient (rate of temperature change)
for cooling or allowing the CCD to warm back is less than 5 K/minute.
Features
Multichannel detector heads C7040, C7041
C7040: for S7030 series
C7041: for S7031 series
Area scanning or full line-binnng operation
Readout frequency: 250 kHz
Readout noise: 20 e- rms
'T=50 °C ('T changes by cooling method.)
Input
Supply voltage
Master start
Master clock
Symbol
VD1
VA1+
VA1-
VA2
VD2
Vp
VF
Ims
Imc
Value
+5 Vdc, 200 mA
+15 Vdc, +100 mA
-15 Vdc, -100 mA
+24 Vdc, 30 mA
+5 Vdc, 30 mA (C7041)
+5 Vdc, 2.5 A (C7041)
+12 Vdc, 100 mA (C7041)
HCMOS logic compatible
HCMOS logic compatible,
1 MHz
Information described in this material is current as of January, 2011. Product specifications are subject to change without prior notice due to improvements or other
reasons. Before assembly into final products, please contact us for the delivery specification sheet to check the latest information.
Type numbers of products listed in the delivery specification sheets or supplied as samples may have a suffix "(X)" which means preliminary specifications or a suffix
"(Z)" which means developmental specifications.
The product warranty is valid for one year after delivery and is limited to product repair or replacement for defects discovered and reported to us within that one year
period. However, even if within the warranty period we accept absolutely no liability for any loss caused by natural disasters or improper product use.
Copying or reprinting the contents described in this material in whole or in part is prohibited without our prior permission.
www.hamamatsu.com
HAMAMATSU PHOTONICS K.K., Solid State Division
1126-1 Ichino-cho, Higashi-ku, Hamamatsu City, 435-8558 Japan, Telephone: [phone], Fax: [phone]
U.S.A.: Hamamatsu Corporation: 360 Foothill Road, P.O.Box 6910, Bridgewater, N.J. 08807-0910, U.S.A., Telephone: [phone], Fax: [phone]
Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: [phone], Fax: [phone]
France: Hamamatsu Photonics France S.A.R.L.: 19, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: [phone], Fax: [phone]
United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road, Welwyn Garden City, Hertfordshire AL7 1BW, United Kingdom, Telephone: [phone], Fax: [phone]
North Europe: Hamamatsu Photonics Norden AB: Smidesvägen 12, SE-171 41 Solna, Sweden, Telephone: [phone], Fax: [phone]
Italy: Hamamatsu Photonics Italia S.R.L.: Strada della Moia, 1 int. 6, 20020 Arese, (Milano), Italy, Telephone: [phone], Fax: [phone]
12
Cat. No. KMPD1023E17 Jan. 2011 DN