|
GS81314PQ19GK-800 Datasheet, PDF (4/39 Pages) GSI Technology – Burst of 2 Single-Bank ECCRAM | |||
|
◁ |
GS81314PQ19/37GK-933/800
Pin Description
Symbol
Description
SA[21:0]
D[35:0]
DINV[3:0]
Q[35:0]
QINV[3:0]
QVLD[1:0]
CK, CK
KD[1:0],
KD[1:0]
CQ[1:0],
CQ[1:0]
R
W
MRW
PLL
RST
Address â Read address is registered on ïCK and write address is registered on ïCK.
Write Data â Registered on ïKD and ïKD during Write operations.
D[17:0] - x18 and x36.
D[35:18] - x36 only.
Write Data Inversion â Registered on ïKD and ïKD (along with write data) during Write operations. ï
Indicate if the associated write data byte is inverted (DINVx = 1) or not (DINVx = 0).
DINV0 - associated with D[8:0] in x18 and x36.
DINV1 - associated with D[17:9] in x18 and x36.
DINV2 - associated with D[26:18] in x36 only.
DINV3 - associated with D[35:27] in x36 only.
Note: Treated as NU inputs when Data Inversion is disabled.
Read Data â Aligned with ïCQ and ïCQ during Read operations.
Q[17:0] - x18 and x36.
Q[35:18] - x36 only.
Read Data Inversion â Aligned with ïCQ and ïCQ (along with read data) during Read operations. ï
Indicate if the associated read data byte is inverted (QINVx = 1) or not (QINVx = 0).
QINV0 - associated with Q[8:0] in x18 and x36.
QINV1 - associated with Q[17:9] in x18 and x36.
QINV2 - associated with Q[26:18] in x36 only.
QINV3 - associated with Q[35:27] in x36 only.
Note: Treated as NU outputs when Data Inversion is disabled.
Read Data Valid â Driven high one half cycle before valid read data.
Primary Input Clocks â Dual single-ended. Used for latching address and control inputs, for internal timing
control, and for output timing control.
Write Data Input Clocks â Dual single-ended. Used for latching write data inputs.
KD0, KD0: latch D[17:0], DINV[1:0] in x36, and D[8:0], DINV0 in x18.
KD1, KD1: latch D[35:18], DINV[3:2] in x36, and D[17:9], DINV1 in x18.
Read Data Output Clocks â Free-running output (echo) clocks, tightly aligned with read data outputs.
Facilitate source-synchronous operation.
CQ0, CQ0: align with Q[17:0], QINV[1:0] in x36, and Q[8:0], QINV0 in x18.
CQ1, CQ1: align with Q[35:18], QINV[3:2] in x36, and Q[17:9], QINV1 in x18.
Read Enable â Registered on ïCK. See the Clock Truth Table for functionality.
Write Enable â Registered on ïCK. See the Clock Truth Table for functionality.
Mode Register Write â Registered onïCK. Can be used synchronously or asynchronously to enable Reg-
ister Write Mode. See the State and Clock Truth Tables for functionality.
PLL Enable â Weakly pulled High internally.
PLL = 0: disables internal PLL.
PLL = 1: enables internal PLL.
Reset â Holds the device inactive and resets the device to its initial power-on state when asserted High.
Weakly pulled Low internally.
Type
Input
Input
Input
Output
Output
Output
Input
Input
Output
Input
Input
Input
Input
Input
Rev: 1.02 3/2016
4/39
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2015, GSI Technology
|
▷ |