HB Datasheet, PDF (2/2 Pages) List of Unclassifed Manufacturers – EM Hysteresis Brake

Illuminated Switches
Illuminated Subminiature Pushbutton Switches
HB Series
S 9mm, Square
The bezel is an
integral part of
the switch body.
SHAPES & PANEL CUTOUT
C 9mm Round
Recommemded Panel Thickness: 0.5 ~
5.0 mm. Socket wrench AT110 may be
used for mounting. Overtightening the
mounting nut AT073 may damage the
switch housing.
(8.0) Dia
.315
CAPS FOR NON-ILLUMINATED SWITCHES
CAPS FOR BRIGHT LEDs
AT4035
(7.4) Sq
.291
(4.5)
.177
(4.8)
.189
AT4036
(7.4) Dia
.291
(4.5)
.177
(4.8)
.189
AT4052 Spot Illuminated AT4166
(7.4) Sq
.291
(4.6)
.181
(4.8)
.189
(1.8)
.071
(1.2)
.047
(3.0)
.118
(4.8)
.189
(7.4) Sq
.291
(4.5)
.177
AT4167
(7.4) Dia
.291
(4.5)
.177
(4.8)
.189
Transparent Colored Lens
Translucent White Diffuser
CAPS FOR BRIGHT & SUPER BRIGHT LEDs
TERMINALS
Colored LED
AT4031
(7.4) Sq
.291
(4.5)
.177
(4.8)
.189
AT4032
(7.4) Dia
.291
(4.5)
.177
(4.8)
.189
W01 Solder Lug
The 1.0x2.0mm oblong hole accommodates one
solid or one stranded 20-gauge wire or two 22-
gauge wires.
Solder lug terminals are spaced 2.54x5.08mm. This
enables PCB mounting which can be accommplis-
hed by elongating PC board hole to 2.03mm.
(2.0)
.079
(1.0)
.039
(5.0)
.197
(1.8)
.071
Thk = (0.3)
.012
LED COLORS & SPECIFICATIONS
Bright
AT633
(+)
(-)
Bright
Super Bright
5C
5D
5F
6B
6F
6G
Red
Amber Green White Green
Blue
Unit
Super Bright
AT624G (Blue)
AT629B (White)
AT630F (Green)
T-1 Bi-pin
Forward Peak Current
I_FM
Continuous Forward Current
I
F
Forward Voltage
V
F
Reverse Peak Voltage
V_RM
Current Reduction Rate Above 25°C ¨I_F
Ambient Temperature Range
30
30
25
30
30
30
mA
20
20
20
20
20
20
mA
1.85
2.0
2.2
3.6
3.5
3.6
V
5
5
5
5
5
5
V
0.40
0.42
0.38
0.50
0.50
0.50
mA/°C
-25 ~ +50
°C
The electrical specifications shown are determined at a basic temperature of 25°C. LED circuit is isolated and requires external power source. Single element LED is colored in OFF state. If the source voltage exceeds the
rated voltage, a ballast resistor is required.
Cap Removal
ASSEMBLY INSTRUCTIONS
LED Polarity & Orienation in Lamp Socket
Cap Replacement
D Flat
Black Dot
AT624
AT629
AT630
(+)
(–)
(+)
(–) AT633
Top View
of Switch
Anode
(+)
Cathode
(–)
AT111 Lamping Tool
AT110 Socket Wrench
Lamping Tool AT111 may be used to remove and replace LED.
2 [e-mail]
Socket Wrench AT110 may be used to tighten the mounting nut.
www.greatecs.com