G9612 Datasheet, PDF (2/8 Pages) Global Mixed-mode Technology Inc – Low-Dropout, 500mA Linear Regulator with Reset

Global Mixed-mode Technology Inc.
G9612
Absolute Maximum Ratings
Supply Voltage (IN or OUT to GND)…...…0.3V to 6.5V
Input Voltage….………………………………………6.5V
Thermal Resistance Junction to Ambient, (θ_JA)
SOT-89-5...……………………….….……….…135°C/W
Thermal Resistance Junction to Case, (θ_Jc)
SOT-89-5..…….………………….….….……..…24°C/W
Output Short-Circuit Duration…….…….….……1 min
Operating Temperature Range…….....-40°C to 85°C
Junction Temperature………………….………..160°C
Storage Temperature Range…...……-65°C to 160°C
Reflow Temperature (soldering, 10sec)………260°C
Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the
specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability
Electrical Characteristics
V_IN=5V, C_IN=1µF, C_OUT=10µF, T_J =T_A=25°C (Note3), unless otherwise noted. Typical values for regulators are
at V_IN =5V.
PARAMETER
Input Voltage
Output Voltage (Note 1)
Load Regulation
Line Regulation
Dropout Voltage (Note 2)
Parameter Tempco V_OUT
Ripple Rejection
Output Noise
Quiescent Current
Foldback Current Limit
Foldback Voltage
Thermal Shutdown Temperature
Thermal Shutdown Hysteresis
Reset Threshold
Reset Threshold Hysteresis
Reset Threshold Tempco
C_D Delay Pin Threshold Voltage
C_D Pin Sink Current
C_D Pin Pullup Resistance
RESET Output Current Low
RESET Function Operating Voltage
SYMBOL
CONDITION
V_IN
G9612A
V_OUT G9612B/C
G9612D
ΔV_LDR
ΔV_LNR
ΔV_DO
I_OUT=1mA to 500mA, V_IN=V_OUT +1V
(V_OUT+0.5V) ≤ V_IN ≤ 6V, I_OUT =25mA
I_OUT=500mA
G9612A/B/C
G9612D
PSRR
e_n
f=120HZ, I_OUT=30mA
f=120HZ, I_OUT=300mA
20Hz to 100kHz, I_OUT=30mA~500mA.
I_Q
I_LIM
V_OUT<V_FOLDBACK
V_OUT>V_FOLDBACK
V_FOLDBACK
T_SD
ΔT_SD
G9612A/B/D
V_TH-
G9612C
V_HYS
G9612A/B/D
G9612C
V_TCD
I_CD
R_D
I_OL
V_OP
V_CC = 5V
V_CC=1.5V, V_CD=0.5V
V_CC=2.5V, V RESET =0.4V
RESET sink current>10µA
MIN
2.5
3.332
3.234
2.45
---
-8
---
---
---
---
---
---
---
260
650
0.6
---
---
4.11
3.81
---
---
---
3.5
3
100
8
---
TYP
---
3.4
3.3
2.5
8
0.3
560
650
40
70
65
320
320
400
900
0.78
160
30
4.2
3.9
150
130
40
3.9
4.3
200
11.5
0.7
MAX
6.0
3.468
3.366
2.55
17
8
610
700
---
---
---
---
450
580
1200
0.95
---
---
4.29
3.99
---
---
---
4.3
---
400
---
0.85
UNIT
V
V
mV
mV
mV
ppm/°C
dB
µ^VRMS
µA
mA
V
°C
°C
V
mV
ppm/°C
V
mA
kΩ
mA
V
Note 1:
Note 2:
Note 3:
(V_IN-V_OUT) is limited to keep the product (I_OUT x (V_IN - V_OUT)) from exceeding the package power dissipation limits.
Dropout Voltage is (V_IN - V_OUT) when V_OUT falls to 100mV below its nominal value at V_IN = V_OUT+1V. For example, the
G9612 is tested by measuring the V_OUT at V_IN = V_OUT+1V, then V_IN is lowered until V_OUT falls 100mV below the meas-
ured value. The difference (V_IN - V_OUT) is then measured and defined as ΔV_DO.
Low duty pulse techniques are used during test to maintain junction temperature as close to ambient as possible.
Ver: 1.7
Apr 01, 2005
TEL: [phone]
http://www.gmt.com.tw
2