050_344 Datasheet, PDF (2/16 Pages) Glenair, Inc. – FMC CONNECTIVITY CARD

050-344
FMC CONNECTIVITY CARD
For Glenair PCB Mount Opto-Electronic Converters
Glenair 050-344 FPGA Mezzanine Card (FMC) Connectivity Card provides a
convenient method to easily incorporate a wide range of Glenair Harsh
Environment PCB Mount Transceiver, Transmitter and Receiver products as
well as Glenair size 8 Opto-electronic transmitter and receiver contacts into
FPGA based systems. It is compatible with Xilinx® evaluation boards with
FMC connector(s) board and uses the High Pin Count (HPC) version of the
FMC connector.
This FMC card is offered in three configurations, see how to order information,
to support all categories of Glenair PCB Mount devices. Electrical
connections to PCB Mount Opto-electronic devices are through high speed
Samtec connector mounted on the 050-344 card. The card has an FMC
High Pin Count (HPC) connector to mate to the Host FPGA carrier board
which interface with four high-speed serial transceivers on the FPGA carrier
board. It is compatible with either HPC or Low Pin Count (LPC) connector
(restricted to single high-speed serial transceiver for LPC) on the host board.
The 050-344 card also incorporates LEDs for RX LOS indications as well as a
low-jitter 156.25MHz oscillator for use as a clock source for the high-speed
serial transceivers. The board also incorporates I²C current monitor IC and
an I²C GPIO IC so each DUT can be monitored. 22 GPIO pins are also made
available for the user.
KEY FEATURES/BENEFITS




Industry standard, modular FPGA I/O in FMC
(VITA 57.1) module
Supports large variety of Opto-Electronic devices
suitable for Harsh Environment (Wide temperature
ranges and Extremely High Vibration) applications
such as: Airborne Tactical Military, Oil and Gas,
Industrial, Railway and Aerospace
o 10 Mbps to 12.5 Gbps
Direct connections between Glenair PCB Mount
transceivers and host FPGA ensures maximum
throughput and minimum latency
HPC – High Pin Count FMC
o Provides access to 4 high speed transceivers
o Compatible with LPC Host board connectors
as well but then restricted to single high-
speed transceiver (DP0)
 Low-jitter 156.25 MHz Clock source, Sampling
Frequency and Calibration from via SPI
communication bus
 SFF 8472 Digital Diagnostic Monitoring (DMI) can
be accessed from host board via I²C or via
connector Header
 I²C GPIO for current monitoring, RX_LOS,
TX_FAULT, TX_DISABLE control and signaling
APPLICATIONS
 As an evaluation tool for Glenair Opto-electronic
modules which are suited to Harsh Environment
Applications such as: Airborne, Tactical Military,
Oil and Gas, Railway and Shipboard
o Ethernet, Fibrechannel, 1x, 2x, 4x, 8x,
SFPDP, Aurora
o Video (DVI, SMPTE, ARINC818, etc)
HOW TO ORDER
Part
Description of
Glenair Opto-Electronic Existing and Planned
Number Products to be tested
Products supported:
050-344-A Transceivers,
050-315, 050-318, 050-321, 050-324, 050-327,
050-340, 050-341, 050-342, 050-343
Dual-Transceivers
050-333
Size 8 TX & RX OE Contacts 050-301, 050-307
050-344-B Dual-Transmitters
050-316, 050-319, 050-325, 050-331,
Dual-Receivers
050-317, 050-320, 050-326, 050-332
050-344-C Quad-Transmitters
050-336,
Quad-Receivers
050-337
©2014 Glenair, Inc.
REV: 3
US Cage Code 06324
Printed in USA
GLENAIR, INC. ∙ 1211 AIR WAY ∙ GLENDALE, CA 91201-2497 ∙ TEL: [phone] ∙ FAX: [phone]
www.glenair.com
PAGE 2 of 16
E-mail: [e-mail]