852-056 Datasheet, PDF (1/2 Pages) Glenair, Inc. – Mighty Mouse Connectors

Mighty Mouse Connectors with Size #8 Quadrax, Twinax,
Coax or Power Contacts
Size #8 75 Ohm Coax Contacts 852-056-01 and 852-057-01
Size #8 coax contacts for 75 ohm video cable
Size 8 coax contacts fit aerospace-grade digital video cable. 75 ohm nominal
K
impedance. 0-4 GHz frequency range. Crimp termination. Supplied as unassembled
kit with contact body, center contact, outer ferrule and optional sealing boot.
These snap-in, rear-release contacts fit Glenair Series 80 Mighty Mouse connectors
and MIL-DTL-38999 Series I, III and IV connectors with size 8 contact cavities. Use
with aerospace-grade video cable shown on next page. Gold-plated copper alloy,
Teflon® insulator.
.562 (14.27)
MAX
.517 (13.13)
± .003 (0.08)
Fig.
Fig. 1
Fig. 2
Contact
Type
Pin
Socket
Part Number
Contact Only
852-056-01
852-057-01
Part Number
Contact and Sealing
Boot
852-056-01F
852-057-01F
.562 (14.27)
MAX
.625 (15.88)
± .006 (0.15)
Sealing Boot
859-042-01
859-042-01
Ø .0240 ± .0005
(0.61 ± 0.01)
.219 (5.56) Ø.316 (8.03)
.217 (5.51) .313 (7.95)
Ø.316 (8.03)
.313 (7.95)
.218 (5.54)
HEX CRIMP
.033 (0.84)
.029 (0.74)
Fig. 1  Pin Contact
852-056-01
.218 (5.54)
HEX CRIMP
.033 (0.84)
.029 (0.74)
Fig. 2  Socket Contact
852-057-01
Materials, Finishes
Contact body, center
contact, ferrule
Copper Alloy
Contact finish
50 microinches gold
over nickel plating
Dielectric
Teflon®
Specifications
DESCRIPTION
REQUIREMENT
Nominal Impedance
75 Ohms
Frequency Range
0 – 4 GHz
Dielectric Withstanding Voltage
1300 Vac sea level, 250 Vac at 50,000 feet
Insulation Resistance
5000 megohms minimum
Durability
500 mating cycles
Contact Removal Tool
Plastic tool extracts wired contact from
connector. First, remove sealing boot,
then insert tool from rear of connector.
Size
Part Number
Military Part
Number
#8
859-049
M81969/14-12
Sealing Boot
Optional sealing boot is recommended.
Slide boot onto wire before terminating
contact. After contact is installed in
connector, slide boot forward into
connector grommet to seal the contact
cavity. "F" suffix on contact part number
specifies contact supplied with 859-
042-01 sealing boot.
Wire Dia.
(in.)
.090 - .130
.130 - .170
.170 - .205
Wire Dia.
(mm.)
2.3 - 3.3
3.3 - 4.3
4.3 - 5.2
Part Number
859-042-01
859-042-02
859-042-03
.985 (25.02)
MAX
.350
(8.89)
.326
(8.28)
Dimensions in Inches (millimeters) are subject to change without notice.
© 2014 Glenair, Inc.
Series 80 Mighty Mouse
U.S. CAGE Code 06324
Printed in U.S.A.
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX [phone]
www.glenair.com
K-24
E-Mail: [e-mail]