852-042 Datasheet, PDF (1/2 Pages) Glenair, Inc. – Mighty Mouse Connectors

Mighty Mouse Connectors with Size #8 Quadrax, Twinax,
Coax or Power Contacts
Size #8 50 Ohm Coax Contacts 852-042 and 852-043
Size #8 50 ohm contacts for low loss high performance coax cable
K
Coax contacts fit Glenair Series 80 Mighty Mouse connectors and MIL-DTL-38999
Series I, III and IV connectors with size 8 contact cavities. 50 ohm nominal
impedance. 0-2.5 GHz frequency range. Solder conductor to center contact is
solder type, shield termination is crimp type. Supplied as unassembled kit with
contact body, center contact, outer ferrule and sealing boot. Contacts are snap-in,
rear release with plastic extraction tool. Gold-plated copper alloy, Teflon® insulator.
See following page for information on coaxial cable.
.562 (14.27)
MAX
.517 (13.13)
± .003 (0.08)
Fig.
Fig. 1
Fig. 2
Contact
Type
Pin
Socket
Part Number
Contact Only
852-043
852-042
Part Number
Contact and Sealing
Boot
852-043F
852-042F
Sealing Boot
859-042-02
859-042-02
.562 (14.27)
MAX
.625 (15.88)
± .006 (0.15)
Ø .0355 ± .001
(0.90 ± 0.03)
.219 (5.56) ^{Ø.316 (8.03)}
.217 (5.51) ^{.313 (7.95)}
Ø.316 (8.03)
.313 (7.95)
.213 (5.41)
HEX CRIMP
.033 (0.84)
.029 (0.74)
Materials, Finishes
Contact body, center
contact, ferrule
Copper Alloy
Contact finish
50 microinches gold
over nickel plating
Dielectric
Fluorocarbon
Fig. 1  Pin Contact
852-043
.213 (5.41)
HEX CRIMP
.033 (0.84) _{Fig. 2  Socket Contact}
.029 (0.74)
852-042
Specifications
DESCRIPTION
REQUIREMENT
Nominal Impedance
50 Ohms
Frequency Range
0 – 2.5 GHz
Dielectric Withstanding Voltage
1300 Vac sea level, 250 Vac at 50,000 feet
Insulation Resistance
5000 megohms minimum
Durability
500 mating cycles
Contact Removal Tool
Plastic tool extracts wired contact from
connector. First, remove sealing boot,
then insert tool from rear of connector.
Size Part Number
Military Part
Number
#8
859-049
M81969/14-12
Sealing Boot
Optional sealing boot is recommended.
Slide boot onto wire before terminating
contact. After contact is installed in
connector, slide boot forward into
connector grommet to seal the contact
cavity. "F" suffix on contact part number
specifies contact supplied with 859-
042-02 sealing boot.
Wire Dia. (in.)
.090 - .130
.130 - .170
.170 - .205
Wire Dia.
(mm.)
2.3 - 3.3
3.3 - 4.3
4.3 - 5.2
.985 (25.02)
MAX
Part Number
859-042-01
859-042-02
859-042-03
.350
(8.89)
.326
(8.28)
Dimensions in Inches (millimeters) are subject to change without notice.
© 2014 Glenair, Inc.
Series 80 Mighty Mouse
U.S. CAGE Code 06324
Rev. 07.07.15 Printed in U.S.A.
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX [phone]
www.glenair.com
K-26
E-Mail: [e-mail]