712AS419XM19 Datasheet, PDF (1/1 Pages) Glenair, Inc. – Self-Locking Composite Conduit Adapter

712-419
Self-Locking Composite Conduit Adapter for
Series 74 PEEK, PFA, ETFE, FEP or PTFE Tubing
Shielding Optional
712 F T 419 XM 19 12-20 K-1 A
Product Series
Connector Designator
(A, F, H & U)
Angular Function
S - Straight
T = 45° Elbow
W = 90° Elbow
Basic No.
Finish (Table III)
Shell Size (Table I) (See Note 1)
Dash No. (Table II)
Optional Length (See Note 3)
Symbol "S" only
Tubing Option (See Note 2)
K = PEEK (Omit for PFA, ETFE, FEP, or PTFE)
To accommodate EMI or Dacron overbraid
(Omit if Not Required)
Add Letter for Optional Configuration
(See Detail A and Note 4)
A Thread Typ.
(See Note 1)
1.250
(31.8)
K - Entry
Tubing shown for reference
only (See Note1)
C
Anti-
Decoupling
Device
G
Tubing I.D.
(see Note 2)
J
Typ
Sym S – Straight Knurl or Flute Style Manufacurer's
Option, Typ.
E
F
Sym W
90°
H
Sym T
45°
Raised configuration
(Mfr's option)
Dash 1 configuration EMI or Dacron
over Braid (See P/N Development)
Shell Size
A,F & H G & U
08, 09
03, 10, 11
12, 13
14, 15
16, 17
18, 19
20, 21
22, 23
24, 25, 61
28
–
08
10, 11
12, 13
14, 15
16, 17
18, 19
20
22, 23
24, 25
E
+.06 (1.5)
.720 (18.3)
.750 (19.1)
.750 (19.1)
.760 (19.3)
.780 (19.8)
.790 (20.1)
.820 (20.8)
.860 (21.8)
.890 (22.6)
.920 (23.4)
Table I
F
+.09 (2.3)
.890 (22.6)
.950 (24.1)
1.020 (25.9)
1.050 (26.7)
1.070 (27.2)
1.080 (27.4)
1.110 (28.2)
1.150 (29.2)
1.180 (30.0)
1.210 (30.7)
G
+.06 (1.5)
.690 (17.5)
.750 (19.1)
.810 (20.6)
.880 (22.4)
.940 (23.9)
.970 (24.6)
1.060 (26.9)
1.130 (28.7)
1.190 (30.2)
1.340 (34.0)
H
Tubing
+.09 (2.3) Size Max.
1.110 (28.2) 09
1.160 (29.5) 12
1.220 (31.0) 16
1.290 (32.8) 20
1.350 (34.3) 24
1.380 (35.1) 28
1.470 (37.3) 32
1.540 (39.1) 32
1.730 (43.9) 40
1.820 (46.2) 40
Table II
TTaAbBlLeEII2I
Dash Conduit
J Dia
No.
I.D.
Max
K
Entry
XM Electroless Nickel
06 .188 (4.8) .540 (13.7) .120 (3.0) ^{XW Cadmium Olive Drab Over Electroless}
09 .281 (7.1) .630 (16.0) .220 (5.6)
Nickel
10 .312 (7.9) .690 (17.5) .240 (6.1) XB No Plating - Black Material
12 .375 (9.5) .730 (18.5) .290 (7.4) _{XO No Plating - Base Material}
14 .437 (11.1) .800 (20.3) .340 (8.6)
Non-conductive
16 .500 (12.7) .870 (22.1) .400 (10.2) _NOTES:
20 .625 (15.9) 1.000 (25.4) .520 (13.2) 1. Convoluted tubing size, tubing to be ordered seperately (see Series 74
24 .750 (19.1) 1.180
28 .875 (22.2) 1.320
32 1.000 (25.4) 1.470
(30.0) .650
(33.5) .780
(37.3) .900
(16.5)
(19.8)
(22.9)
Catalog, Type A Tubing Section, Standard Pitch). Dash 1 configuration
accommodates Type B or D Tubing.
2. Different adapters are necessary to terminate PEEK tubing. Nominal I.D.
reduced by approximately .060 (use Suffix P) in P/N development.
40 1.250 (31.8) 1.760 (53.3) 1.080 (27.4) 3. Add optional length in 1/4 inch increments: 20 = 5.00 inches.
48 1.500 (38.1) 2.130
(54.1) 1.320
(33.5)
Omit for standard 1.250 length.
4. For permanant installation suse 3M Scotch Weld Tape after installing
Metric dimensions (mm) are in parentheses and are for reference only. _{tubing/shield (see Detail A).}
© 2003 Glenair, Inc.
CAGE Codes 06324
Printed in U.S.A.
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX [phone]
www.glenair.com
D-32
E-Mail: [e-mail]