181-043-15 Datasheet, PDF (1/1 Pages) Glenair, Inc. – MIL-PRF-29504/18 Type Terminus

181-043
MIL-PRF-29504/18 Type Terminus
for MIL-PRF-62466 (NGCON) Fiber Optic Connectors
M64266
NGCON
0
8
H
MIL-PRF-29504/18 and /20 type NGCON genderless rear-release termini with
integrated retention clip and environmental seal
Part Number Part Number ØA
Non-Keyed
Keyed
(Micron)
181-043-1250C 181-043K-1250C 125.0
181-043-1255C 181-043K-1255C 125.5
181-043-126SC 181-043K-126SC 126.0
181-043-126C 181-043K-126C 126.0
181-043-127C 181-043K-127C 127.0
181-043-142C 181-043K-142C 142.0
181-043-145C 181-043K-145C 145.0
181-043-156C 181-043K-156C 156.0
181-043-157C 181-043K-157C 157.0
181-043-173C 181-043K-173C 173.0
181-043-175C 181-043K-175C 175.0
Consult factory for additional sizes.
SM = Singlemode • MM = Multimode
Table I
Typical Typical Fiber Size
Ref.
Ref.
Fiber Core/Cladding/Coating M29504/18-XX M29504/20-XX
Type
(Micron)
Non-Keyed
Keyed
SM
9/125
M29504/18-01 M29504/20-01
SM
9/125
M29504/18-02 M29504/20-02
SM/MM
9/125, 50/125,
62.5/125
M29504/18-03 M29504/20-03
MM
50/125, 62.5/125 M29504/18-26 M29504/20-26
MM
50/125, 62.5/125 M29504/18-27 M29504/20-27
MM
100/140
M29504/18-42 M29504/20-42
MM
100/140
M29504/18-45 M29504/20-45
MM
62.5/125/155 M29504/18-56 M29504/20-56
MM
62.5/125/155 M29504/18-57 M29504/20-57
MM
100/140/172 M29504/18-73 M29504/20-73
MM
100/140/172 M29504/18-75 M29504/20-75
1.160 Max
.233 Min
Ø1.25 mm
Ferrule
Od
Terminus Body
Key (When Specified In Part Number)
ØA
Ferrule
Hole
Ferrule
Table II: Accessories
Part No.
Description
181-043-C
Crimp Sleeve, Ø2.4mm
Max Jacket
182-012
Crimp tool
182-013
Insertion tool, straight
182-014
Insertion tool, 90°
182-021
Hand polishing tool
182-025
Removal tool
Seal
Compression ^{Ø.127 Max}
Ø.077
Crimp Sleeve
Bushing
Material and Finish
Ferrule: Zirconia Ceramic
Terminus Assembly: Stainless steel/passivate
Retention Clip: Spring alloy
Spring: Stainless steel/passivate
Seal: Elastomeric rubber
Crimp Sleeve: Stainless steel/passivate
Accessories
Consult factory for appropriate termination and assembly tools/procedures
Crimp sleeve is supplied with terminus assembly, and may be ordered separately (see Table II).
For terminus less crimp sleeve, omit “C” from part number
Notes
181-043 non-keyed termini can be used with 180-118 connectors with or without keyed cavities.
For dummy terminus, see Glenair drawing 181-078
© 2012 Glenair, Inc.
U.S. CAGE Code 06324
Rev. 05.06.15
Printed in U.S.A.
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX [phone]
www.glenair.com
H-2
E-Mail: [e-mail]