SBLF2030CT Datasheet, PDF (1/2 Pages) General Semiconductor – SCHOTTKY ISOLATED PLASTIC RECTIFIER

NEW PRODUCT
NEW PRODUCT
NEW PRODUCT
SBLF2030CT AND SBLF2040CT
SCHOTTKY ISOLATED PLASTIC RECTIFIER
Reverse Voltage - 30 and 40 Volts Forward Current - 20.0 Amperes
ITO-220AB
0.405 (10.27)
0.383 (9.72)
0.140 (3.56)
DIA.
0.130 (3.30)
0.600 (15.5)
0.580 (14.5)
0.560 (14.22)
0.530 (13.46)
PIN
1
2
3
0.676 (17.2)
0.646 (16.4)
0.191 (4.85)
0.171 (4.35)
0.060 (1.52)
0.350 (8.89)
0.330 (8.38)
0.188 (4.77)
0.172 (4.36)
0.110 (2.80)
0.100 (2.54)
0.131 (3.39)
0.122 (3.08) ^DIA.
0.110 (2.80)
0.100 (2.54)
FEATURES
¨ Isolated plastic package has Underwriters Laboratory
Flammability Classifications 94V-0
¨ Metal silicon junction,
majority carrier conduction
¨ Low power loss, high efficiency
¨ High current capability,
low forward voltage drop
¨ High surge capability
¨ For use in low voltage, high frequency inverters,
free wheeling, and polarity protection applications
¨ Dual rectifier construction, positive center-tap
¨ Guardring for overvoltage protection
¨ High temperature soldering guaranteed:
250°C/10 seconds, 0.16" (4.04mm) from case
0.205 (5.20)
0.195 (4.95)
0.037 (0.94)
0.027 (0.69)
0.105 (2.67)
0.095 (2.41)
PIN 1
PIN 3
0.022 (0.55)
0.014 (0.36)
PIN 2
Dimensions in inches and (millimeters)
MECHANICAL DATA
Case: JEDEC ITO-220AB fully overmolded plastic body
Terminals: Leads solderable per MIL-STD-750,
Method 2026
Polarity: As marked
Mounting Position: Any
Weight: 0.08 ounce, 2.24 grams
Mounting Torque: 5 in. - lbs.max.
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25°C ambient temperature unless otherwise specified
Maximum repetitive peak reverse voltage
Maximum RMS voltage
Maximum DC blocking voltage
Maximum average forward rectified current
at TC=105¡C
Peak forward surge current, 8.3ms single
half sine-wave superimposed on rated load
(JEDEC Method)
Peak repetitive reverse surge current (NOTE 3)
Maximum instantaneous forward voltage
per leg at 10.0A (NOTE 1)
Maximum instantaneous current at
TC=25¡C
rated DC blocking voltage per leg (NOTE 1) TC=100¡C
Typical thermal resistance per leg (NOTE 2)
Operating junction and storage temperature range
RMS Isolation voltage from terminals to heatsink
with RH ² 30%
SYMBOLS
VRRM
VRMS
VDC
I(AV)
IFSM
IRRM
VF
IR
RQJC
TJ, TSTG
VISOL
SBLF2030CT
30
21
30
SBLF2040CT
40
28
40
20.0
175.0
1.0
0.55
1.0
50.0
4.0
-40 to +125
4500 (NOTE 4)
3500 (NOTE 5)
1500 (NOTE 6)
NOTES:
(1) Pulse test: 300ms pulse width, 1% duty cyle
(2) Thermal resistance from junction to case per leg
(3) 2.0ms pulse width, f=1.0 KHZ
(4) Clip mounting (on case), where lead does not overlap heatsink with 0.110Ó offset.
(5) Clip mounting (on case), where leads do overlap heatsink.
(6) Screw mounting with 4-40 screw, where washer diameter is £ 4.9 mm (0.19Ó).
2/17/99
UNITS
Volts
Volts
Volts
Amps
Amps
Amp
Volts
mA
¡C/W
¡C
Volts