SBLF1030CT Datasheet, PDF (1/2 Pages) General Semiconductor – SCHOTTKY ISOLATED PLASTIC RECTIFIER

NEW PRODUCT
NEW PRODUCT
NEW PRODUCT
SBLF1030CT AND SBLF1040CT
SCHOTTKY ISOLATED PLASTIC RECTIFIER
Reverse Voltage - 30 and 40 Volts Forward Current - 10.0 Amperes
ITO-220AB
0.405 (10.27)
0.383 (9.72)
0.140 (3.56)
DIA.
0.130 (3.30)
0.600 (15.5)
0.580 (14.5)
0.560 (14.22)
0.530 (13.46)
PIN
1
2
3
0.676 (17.2)
0.646 (16.4)
0.191 (4.85)
0.171 (4.35)
0.060 (1.52)
0.350 (8.89)
0.330 (8.38)
0.188 (4.77)
0.172 (4.36)
0.110 (2.80)
0.100 (2.54)
0.131 (3.39)
DIA.
0.122 (3.08)
0.110 (2.80)
0.100 (2.54)
FEATURES
¨ Isolated plastic package has Underwriters Laboratory
Flammability Classifications 94V-0
¨ Metal silicon junction, majority carrier conduction
¨ Low power loss,high efficiency
¨ High current capability,
low forward voltage drop
¨ High surge capacity
¨ For use in low voltage, high frequency inverters,
free wheeling, and polarity protection applications
¨ Guardring for overvoltage protection
¨ High temperature soldering guaranteed:
250¡C/10 seconds, 0.25" (6.35mm) from case
0.205 (5.20)
0.195 (4.95)
0.037 (0.94)
0.027 (0.69)
0.105 (2.67)
0.095 (2.41)
PIN 1
PIN 3
0.022 (0.55)
0.014 (0.36)
PIN 2
Dimensions in inches and (millimeters)
MECHANICAL DATA
Case: JEDEC ITO-220AB fully overmolded plastic body
Terminals: Lead solderable per MIL-STD-750,
Method 2026
Polarity: As marked
Mounting Position: Any
Mounting Torque: 5 in. - lbs max.
Weight: 0.08 ounce, 2.24 grams
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25¡C ambient temperature unless otherwise specified.
Maximum repetitive peak reverse voltage
Maximum RMS voltage
Maximum DC blocking voltage
Maximum average forward rectified current
at TC=95¡C
Peak forward surge current, 8.3ms single
half sine-wave superimposed on rated load
(JEDEC Method)
Maximum instantaneous forward voltage
per leg at 5.0A (NOTE 1)
Maximum instantaneous reverse current at
rated DC blocking voltage (NOTE 1)
Typical thermal resistance (NOTE 2)
Operating and storage temperature range
RMS Isolation voltage from terminals to heatsink
with RH ² 30%
TC=25¡C
TC=100¡C
SYMBOLS
VRRM
VRMS
VDC
I(AV)
IFSM
VF
IR
RQJC
TJ, TSTG
VISOL
SBLF1030CT
30
21
30
SBLF1040CT
40
28
40
10.0
175.0
0.55
0.5
50.0
5.0
-40 to +125
4500 (NOTE 3)
3500 (NOTE 4)
1500 (NOTE 5)
NOTES:
(1) Pulse test: 300ms pulse width, 1% duty cycle
(2) Thermal resistance from junction to case per leg
(3) Clip mounting (on case), where lead does not overlap heatsink with 0.110Ó offset.
(4) Clip mounting (on case), where leads do overlap heatsink.
(5) Screw mounting with 4-40 screw, where washer diameter is £ 4.9 mm (0.19Ó).
2/17/99
UNITS
Volts
Volts
Volts
Amps
Amps
Volts
mA
¡C/W
¡C
Volts