MBRF735 Datasheet, PDF (1/2 Pages) General Semiconductor – SCHOTTKY ISOLATED PLASTIC RECTIFIER

NEW PRODUCT
NEW PRODUCT
NEW PRODUCT
MBRF735 THRU MBRF760
SCHOTTKY ISOLATED PLASTIC RECTIFIER
Reverse Voltage - 35 to 60 Volts Forward Current - 7.5 Amperes
0.405 (10.27)
0.383 (9.72)
ITO-220AC
0.140 (3.56)
DIA.
0.130 (3.30)
0.600 (15.5)
0.580 (14.5)
0.560 (14.22)
0.530 (13.46)
PIN
1
2
0.676 (17.2)
0.646 (16.4)
0.191 (4.85)
0.171 (4.35)
0.060 (1.52)
0.350 (8.89)
0.330 (8.38)
0.188 (4.77)
0.172 (4.36)
0.110 (2.80)
0.100 (2.54)
0.131 (3.39)
DIA.
0.122 (3.08)
0.110 (2.80)
0.100 (2.54)
FEATURES
¨ Isolated plastic package has Underwriters Laboratory
Flammability Classifications 94V-0
¨ Metal to silicon rectifier,
majority carrier conduction
¨ Low power loss, high efficiency
¨ High current capability, low forward
voltage drop
¨ High surge capability
¨ For use in low voltage, high frequency inverters,
free wheeling, and polarity protection applications
¨ Guardring for overvoltage protection
¨ High temperature soldering guaranteed:
250¡C/10 seconds, 0.25" (6.35mm) from case
0.205 (5.20)
0.195 (4.95)
0.037 (0.94)
0.027 (0.69)
0.022 (0.55)
0.014 (0.36)
PIN 1
PIN 2
Dimensions in inches and (millimeters)
MECHANICAL DATA
Case: JEDEC ITO-220AC fully overmolded plastic body
Terminals: Lead solderable per MIL-STD-750, Method 2026
Polarity: As marked
Mounting Position: Any
Mounting Torque: 5 in. - lbs. max.
Weight: 0.08 ounces, 2.24 grams
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25¡C ambient temperature unless otherwise specified.
Maximum repetitive peak reverse voltage
Maximum working peak reverse voltage
Maximum DC blocking voltage
Maximum average forward rectified current (SEE FIG 1)
Peak repetitive forward current (square wave, 20 KHZ)
at TC=105¡C
Peak forward surge current, 8.3ms single half sine-
wave superimposed on rated load (JEDEC Method)
Peak repetitive reverse surge current (NOTE 1)
Maximum instantaneous
forward voltage at
(NOTE 2)
IF=7.5A, TC=25¡C
IF=7.5A, TC=125¡C
IF=15A, TC=25¡C
IF=15A, TC=125¡C
Maximum instantaneous reverse current at
rated DC blocking voltage
TC=25¡C
(NOTE 1)
TC=125¡C
Voltage rate of change (rated VR)
Maximum thermal resistance, (NOTE 3)
Operating junction temperature range
Storage temperature range
RMS Isolation voltage from terminals to heatsink
with RH ² 30%
SYMBOLS
VRRM
VRWM
VDC
I(AV)
IFRM
IFSM
IRRM
VF
IR
dv/dt
RQJC
TJ
TSTG
VISOL
MBRF735
35
35
35
MBRF745
MBRF50
45
50
45
50
45
50
7.5
15.0
MBRF760
60
60
60
150.0
1.0
0.5
-
0.75
0.57
0.65
0.84
-
0.72
-
0.1
15.0
10,000
5.0
-65 to +150
-65 to +175
4500 (NOTE 4)
3500 (NOTE 5)
1500 (NOTE 6)
0.5
1000
1000
NOTES: (1) 2.0ms, pulse width, f=1.0 KHZ
(2) Pulse test: 300ms pulse width, 1% duty cycle
(3) Thermal resistance from junction to case and/or thermal resistance from junction to ambient
(4) Clip mounting (on case), where lead does not overlap heatsink with 0.110Ó offset.
(5) Clip mounting (on case), where leads do overlap heatsink.
(6) Screw mounting with 4-40 screw, where washer diameter is £ 4.9 mm (0.19Ó).
2/18/99
UNITS
Volts
Volts
Volts
Amps
Amps
Amps
Amps
Volts
mA
V/ms
¡C/W
¡C
¡C
Volts