GP10A Datasheet, PDF (1/2 Pages) Zowie Technology Corporation – SINTERED GLASS PASSIVATED JUNCTION RECTIFIER

GP10A THRU GP10Y
GLASS PASSIVATED JUNCTION RECTIFIER
Reverse Voltage - 50 to 1600 Volts
Forward Current - 1.0 Ampere
*
TED
TEN
PA
DO-204AL
0.107 (2.7)
0.080 (2.0)
DIA.
1.0 (25.4)
MIN.
0.205 (5.2)
0.160 (4.1)
0.034 (0.86)
0.028 (0.71)
DIA.
1.0 (25.4)
MIN.
NOTE: Lead diameter is ^{0.026 (0.66)} for suffix "E" part numbers
0.023 (0.58)
Dimensions in inches and (millimeters)
*Glass-plastic encapsulation is covered by
Patent No. 3,996,602 and brazed-lead assembly by Patent No. 3,930,306
®
FEATURES
♦ Plastic package has
Underwriters
Laboratory Flammability
Classification 94V-0
♦ High temperature metallurgically bonded construction
♦ Glass passivated cavity-free junction
♦ Capable of meeting environmental standards of
MIL-S-19500
♦ 1.0 Ampere operation at TA=75°C and 55°C
with no thermal runaway
♦ Typical IR less than 0.1µA
♦ High temperature soldering guaranteed:
350°C/10 seconds, 0.375" (9.5mm) lead length,
5 lbs. (2.3kg) tension
MECHANICAL DATA
Case: JEDEC DO-204AL molded plastic over glass body
Terminals: Plated axial leads, solderable per MIL-STD-750,
Method 2026
Polarity: Color band denotes cathode end
Mounting Position: Any
Weight: 0.012 ounce, 0.3 gram
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25°C ambient temperature unless otherwise specified.
Maximum repetitive peak reverse voltage
Maximum average forward rectified current
0.375" (9.5mm) lead length (SEE FIG. 1)
Peak forward surge current
8.3ms single half sine-wave superimposed
on rated load (JEDEC Method)
Maximum instantaneous forward voltage at 1.0A
Maximum full load reverse current, full cycle
average, 0.375" (9.5mm) lead lengths at TA=75°C
Maximum DC reverse current
at rated DC blocking voltage
TA=25°C
TA=125°C
Typical reverse recovery time (NOTE 1)
Typical junction capacitance (NOTE 2)
Typical thermal resistance (NOTE 3)
Operating junction and storage temperature range
SYMBOLS A B D G J K M N Q T V W Y UNITS
VRRM
50 to 1600 Volts (SEE FIG. 5)
Volts
I(AV)
1.0
Amp
IFSM
VF
IR(AV)
IR
trr
CJ
RΘJA
TJ, TSTG
30.0
25.0
1.1
8.0
-65 to +175
1.2
1.3
30.0
5.0
50.0
2.0
7.0
55.0
5.0
-65 to +150
Amps
Volts
µA
µA
µs
pF
°C/W
°C
NOTES:
(1) Reverse recovery test condition: IF=0.5A, IR=1.0A, Irr=0.25A
(2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts
(3) Thermal resistance from junction to ambient at 0.375" (9.5mm) lead lengths, P.C.B. mounted
4/98