GI1101 Datasheet, PDF (1/2 Pages) General Semiconductor – GLASS PASSIVATED FAST EFFICIENT RECTIFIER

GI1101 THRU GI1104
GLASS PASSIVATED FAST EFFICIENT RECTIFIER
Reverse Voltage - 50 to 200 Volts Forward Current - 2.5 Amperes
*
TED
DO-204AP
TEN
PA
0.034 (0.86)
0.028 (0.71)
DIA.
1.0 (25.4)
MIN.
0.150 (3.8)
0.100 (2.5)
DIA.
0.240 (6.1)
MAX.
1.0 (25.4)
MIN.
Dimensions in inches and (millimeters)
*Brazed lead assembly is covered by Patent No. 3,930,306
FEATURES
♦ High temperature metallurgically bonded construction
♦ Glass passivated cavity-free junction
♦ Superfast recovery time for high efficiency
♦ Low forward voltage, high current capability
♦ Capable of meeting environmental standards
of MIL-S-19500
♦ Hermetically sealed package
♦ Low Leakage
♦ High surge capability
♦ High temperature soldering guaranteed:
350°C/10 seconds, 0.375" (9.5mm) lead length,
5 lbs. (2.3kg) tension
MECHANICAL DATA
Case: JEDEC DO-204AP solid glass body
Terminals: Plated axial leads, solderable per MIL-STD 750,
Method 2026
Polarity: Color band denotes cathode end
Mounting Position: Any
Weight: 0.02 ounce, 0.56 gram
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25°C ambient temperature unless otherwise specified.
Maximum repetitive peak reverse voltage
Maximum RMS voltage
Maximum DC blocking voltage
Maximum average forward rectified current
0.375" (9.5mm) lead length (SEE FIG.1)
Peak forward surge current
8.3ms single half sine-wave superimposed
on rated load (JEDEC Method) at rated TL
Maximum instantaneous forward voltage at 2.0A
Maximum DC reverse current
at rated DC blocking voltage
TA=25°C
TA=100°C
Maximum reverse recovery time (NOTE 1)
Typical junction capacitance (NOTE 2)
Typical thermal resistance (NOTE 1)
(NOTE 4)
Operating junction and storage temperature range
SYMBOLS
VRRM
VRMS
VDC
I(AV)
IFSM
VF
IR
trr
CJ
RΘJA
RΘJL
TJ, TSTG
GI1101
50
35
50
GI1102
100
70
100
2.5
GI1103
150
105
150
GI1104
200
140
200
2.0
UNITS
Volts
Volts
Volts
Amps
50.0
0.975
2.0
50.0
25.0
45.0
65.0
20.0
-65 to +175
Amps
1.25
(NOTE 5)
10.0
200.0
50.0
Volts
µA
ns
pF
°C/W
-65 to +150 °C
NOTES:
(1) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A
(2) Measured at 1.0 MHZ and applied reverse voltage of 4.0 Volts
(3) Thermal resistance from junction to ambient at 0.375" (9.5mm) lead length and mounted on P.C.B. with 0.5 x 0.5” (12 x 12mm) copper pads
(4) Thermal resistance from junction to lead at 0.375" (9.5mm) lead length with both leads attached to heat sinks
(5) Tested at IF=1.0A
4/98