FEP6AT Datasheet, PDF (1/2 Pages) General Semiconductor – FAST EFFICIENT PLASTIC RECTIFIER

0.160 (4.06)
0.140 (3.56)
FEP6AT THRU FEP6DT
FAST EFFICIENT PLASTIC RECTIFIER
Reverse Voltage - 50 to 200 Volts Forward Current - 6.0 Amperes
TO-220AB
0.415 (10.54) MAX.
0.370 (9.40)
0.360 (9.14)
0.154 (3.91)
DIA.
0.148 (3.74)
0.113 (2.87)
0.103 (2.62)
0.145 (3.68)
0.135 (3.43)
0.410 (10.41)
0.390 (9.91)
PIN
1
23
0.635 (16.13)
0.625 (15.87)
0.350 (8.89)
0.330 (8.38)
1.148 (29.16)
1.118 (28.40)
0.560 (14.22)
0.530 (13.46)
0.185 (4.70)
0.175 (4.44)
0.055 (1.39)
0.045 (1.14)
0.560 (14.22)
0.530 (13.46)
0.110 (2.79)
0.100 (2.54)
FEATURES
♦ Plastic package has Underwriters Laboratory
Flammability Classification 94V-0
♦ Dual rectifier construction, positive center-tap
♦ Glass passivated chip junctions
♦ Superfast recovery times for high efficiency
♦ Low power loss
♦ Low forward voltage, high current capability
♦ For use in low voltage, high frequency inverters,
free wheeling and polarity protection applications
♦ High temperature soldering guaranteed:
250°C, 0.16" (4.06mm) from case for 10 seconds
0.105 (2.67)
0.095 (2.41)
0.037 (0.94)
0.027 (0.68)
0.105 (2.67)
0.095 (2.41)
0.205 (5.20)
0.195 (4.95)
0.022 (0.56)
0.014 (0.35)
PIN 1
PIN 3
Dimensions are in inches and (millimeters)
PIN 2
CASE
MECHANICAL DATA
Case: JEDEC TO-220AB molded plastic body over
passivated chips
Terminals: Plated lead solderable per MIL-STD-750,
Method 2026
Polarity: As marked
Mounting Position: Any
Mounting Torque: 5 in. - lb. max.
Weight: 0.08 ounce, 2.24 grams
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25°C ambient temperature unless otherwise specified.
Maximum repetitive peak reverse voltage
Maximum RMS voltage
Maximum DC blocking voltage
Maximum average forward rectified current at TC=100°
Peak forward surge current
8.3ms single half sine-wave superimposed
on rated load (JEDEC Method)
Maximum instantaneous forward voltage
per leg at 3.0A
Maximum DC reverse current
at rated DC blocking voltage
TC=25°C
TC=100°C
Maximum reverse recovery time per leg (NOTE 1)
Typical thermal resistance (NOTE 2)
(NOTE 3)
Typical junction capacitance per leg (NOTE 4)
Operating junction and storage temperature range
SYMBOLS
VRRM
VRMS
VDC
I(AV)
FEP6AT
50
35
50
FEP6BT FEP6CT
100
150
70
105
100
150
6.0
FEP6DT
200
140
200
UNITS
Volts
Volts
Volts
Amps
IFSM
100.0
Amps
VF
IR
trr
RΘJA
RΘJC
CJ
TJ, TSTG
0.975
5.0
50.0
35.0
20.0
3.6
28.0
-55 to +150
Volts
µA
ns
°C/W
pF
°C
NOTES:
(1) Reverse recovery test conditions: IF=0.5A, Ir=1.0A, Irr=0.25A
(2) Thermal resistance from junction to ambient in free air, no heatsink
(3) Thermal resistance from junction to case per leg mounted on heatsink
(4) Measured at 1.0 MHZ and applied reverse voltage of 4.0 Volts
4/98