BY229X Datasheet, PDF (1/2 Pages) General Semiconductor – FAST SWITCHING PLASTIC RECTIFIER

ADVANCED INFORMATION
ADVANCED INFORMATION ADVANCED INFORMATION
BY229X SERIES
FAST SWITCHING PLASTIC RECTIFIER
Reverse Voltage - 50 to 600 Volts Forward Current - 8.0 Amperes
ITO-220AC
0.405 (10.27)
0.383 (9.72)
0.140 (3.56)
0.130 (3.30) ^DIA.
0.600 (15.5)
0.580 (14.5)
0.560 (14.22)
0.530 (13.46)
PIN
1
2
0.676 (17.2)
0.646 (16.4)
0.191 (4.85)
0.171 (4.35)
0.060 (1.52)
0.350 (8.89)
0.330 (8.38)
0.188 (4.77)
0.172 (4.36)
0.110 (2.80)
0.100 (2.54)
0.131 (3.39)
DIA.
0.122 (3.08)
0.110 (2.80)
0.100 (2.54)
0.205 (5.20)
0.195 (4.95)
0.037 (0.94)
0.027 (0.69)
PIN 1
PIN 2
Dimensions in inches and (millimeters)
0.022 (0.55)
0.014 (0.36)
FEATURES
♦ Plastic package has Underwriters Laboratory
Flammability Classification 94V-0
♦ Glass passivated chip junction
♦ Low leakage, high voltage
♦ High surge current capability
♦ Superfast recovery time, for high efficiency
♦ High temperature soldering guaranteed:
250°C, 0.25" (6.35mm) from case for 10 seconds
MECHANICAL DATA
Case: JEDEC ITO-220AC fully overmolded plastic body
over passivated chip
Terminals: Plated lead solderable per MIL-STD-750,
Method 2026
Polarity: As marked
Mounting Position: Any
Weight: 0.064 ounce, 1.81 grams
Mounting Torque: 5 in. - lbs. max.
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25°C ambient temperature unless otherwise specified.
Maximum recurrent peak reverse voltage
Maximum RMS voltage
Maximum DC blocking voltage
Maximum average forward rectified current
at TC=100°C
Peak forward surge current
8.3ms single half sine-wave superimposed
on rated load (JEDEC Method)
Maximum instantaneous forward voltage at 20A
Maximum DC reverse current
at rated DC blocking voltage
TJ=25°C
at TJ=125°C
Maximum reverse recovery time (NOTE 1)
Maximum recovered stored charge (NOTE 2)
Maximum slope of reverse recovery current (NOTE 2)
Maximum thermal resistance (NOTE 3)
Typical thermal resistance, junction to air
Operating junction and storage temperature range
RMS Isolation voltage from terminals to heatsink
with RH ≤ 30%
SYMBOLS
VRRM
VRMS
VDC
I(AV)
BY229X
-200
200
140
200
IFSM
VF
IR
trr
Qrr
dir/dt
RΘJC
RΘJA
TJ, TSTG
VISOL
BY229X
-400
400
280
400
8.0
BY229X
-600
600
420
600
100
1.85
10.0
300
145
700
60
4.8
20
-40 to +150
4500 (NOTE 4)
3500 (NOTE 5)
1500 (NOTE 6)
NOTES:
(1) Reverse recovery test conditions: IF=1A, VR=30V, di/dt=50A/µs, Irr=10% IRM
(2) Qrr test conditions: IF=2A, VR=30V, di/dt=20A/µs
(3) Thermal resistance from junction to case mounted on heatsink with heatsink compound
(4) Clip mounting, where lead does not overlap heatsink with 0.110” offset.
(5) Clip mounting, where leads do overlap heatsink.
(6) Screw mounting, where washer diameter is ≤ 4.9 mm (0.19”).
10/12/98
BY229X
-800
800
560
800
UNITS
Volts
Volts
Volts
Amps
Amps
Volts
µA
ns
nC
A/µs
°C/W
°C/W
°C
Volts