|
SS-I Datasheet, PDF (1/2 Pages) Gamewell-FCI by Honeywell – Intelligent Addressable Plug-In Ionization Smoke Detector | |||
|
SS-I
Intelligent Addressable Plug-In
Ionization Smoke Detector
Description
Gamewellâs intelligent
SmartScanTM plug-in smoke
detector with integral commu-
nication provides features
that surpass conventional de-
tectors. Detector sensitivity
can be programmed in the
control panel software. Sen-
sitivity is continuously moni-
6934pho1.jpg
tored and reported to the
SS-I with SS-B6 base
panel. Point ID capability al-
lows each detectorâs address
to be set with decade address
switches, providing exact de-
tector locations for selective maintenance when chamber contamination reaches
an unacceptable level. The SS-I ionization detector incorporates a unique single-
source, dual-chamber design to respond quickly and dependably to a broad range of
fires. The SS-I detector is compatible with Gamewellâs 602, 610, 632, 654 and 658
FACPS with a SmartScanTM SLC.
Installation
The SS-I plug-in detector uses a separate base to simplify installation, service, and
maintenance. A special tool allows maintenance personnel to plug in and remove
detectors without using a ladder.
Mount base on an electrical backbox which is at least 1.5" (3.81 cm) deep. Suitable
mounting back boxes include:
⢠4.0" (10.16 cm) square box.
⢠3.5" (8.89 cm) or 4.0" (10.16 cm) octagonal box.
⢠Single-gang box (except for relay or isolator base).
⢠With B501BH or B501BHT base, use a 4.0" (10.16 cm) square box.
⢠With B224RB or B224BI base, use a 3.5" (8.89 cm) octagonal box, or a 4.0"
(10.16 cm) octagonal or square box.
NOTES: 1) Because of the inherent supervision provided by the SLC loop, end-of-
line resistors are not required. Wiring âT-tapsâ or branches are permitted for Style 4
(Class âBâ) wiring. 2) When using relay or sounder bases, consult data sheet CS-
2464 (SS-LI) for device limitations between isolator modules and isolator bases.
Features
⢠Sleek, low-profile design.
⢠Addressable-analog communica-
tion.
⢠Stable communication technique
with noise immunity.
⢠Low standby current.
⢠Two-wire SLC connection.
⢠Rotary, decimal addressing (1 â
99).
⢠Optional remote, single-gang LED
accessory (RA400Z).
⢠Dual LED design provides 360°
viewing angle.
⢠Visible bicolor LEDs blink green
every time the detector is ad-
dressed, and illuminate steady red
on alarm.
⢠Remote test feature from the
panel.
⢠Built-in functional test switch
activated by external magnet.
⢠Built-in tamper-resistant feature.
⢠Sealed against back pressure.
⢠Constructed of off-white
Bayblend®, designed to commer-
cial standards, and offers an
attractive appearance.
⢠94-5V plastic flammability rating.
⢠SEMS screws for wiring of the
separate base.
⢠Optional relay, isolator, or sounder
bases.
⢠Backward-compatible.
Listings
Listings and approvals below
apply to the SS-I Intelligent Plug-In
Ionization Smoke Detector. In
some cases, the detector may not
be listed by certain approval
agencies, or listing may be in
process. Consult factory for latest
listing status.
⢠UL Listed: file S1195.
⢠CSFM approved:
file 7271-1288:168.
Bayblend® is a registered trademark of Bayer Corporation.
SS-I CS-2459 09/01/06
Page 1 of 2
|
▷ |