GF505 Datasheet, PDF (1/2 Pages) Shenzhen Luguang Electronic Technology Co., Ltd – Super Fast Rectifiers

Flex Series
GF505 and GF510
Description
The Flex 505 is a five zone fire alarm control panel (FACP)
and the Flex 510 is a ten zone FACP. These combination
control and digital communicator panels provide reliable
fire signaling protection for medium sized commercial,
industrial and institutional buildings.
Initiating device circuits (IDCs) for Flex Series panels are
programmable and operate in Class B (Style B). Each
panel is compatible with conventional input devices such
as two-wire smoke detectors, four-wire smoke detectors,
pull stations, water flow devices, tamper switches and
other normally-open contact devices. This includes System
Sensor i^3™ Series microprocessor-based detectors with
advanced features like drift compensation, maintenance
alert and freeze warning. (See the Gamewell-FCI Device
Compatibility Document, P/N 52195, for a listing of com-
patible devices).
Outputs include four notification appliance circuits (NACs),
three programmable Form-C relays (factory pre-set for
Alarm, Trouble and Supervisory), and resettable and non
resettable power (24 VDC) for special applications. NACs
are power limited and operate in Class B (Style Y). The
FACP supervises wiring, AC voltage and battery level.
A variety of optional devices can be connected to the built-
in ANN-BUS 4-conductor communication circuit. These
include: remote annunciators, a printer interface module,
LED driver module, and relay module.
Activation of a compatible smoke detector or any normally-
open fire alarm initiating device will activate audible and
visual signaling devices, illuminate an indicating LED, dis-
play message on LCD display, sound the piezo sounder at
the FACP, activate the FACP alarm relay and operate and
optional modules used to notify a remote station or initiate
an auxiliary control function.
Both the Flex 505 and Flex 510 fire alarm control panel are
listed to UL^® Standard 864, 9th Edition.
5 and 10 Zone Conventional
Fire Alarm Control Panels
GF510
Features
• IBC Seismic Certified.
• Class B (Style B) initiating device circuits (IDCs):
- Flex 505 - five programmable IDCs
- Flex 510 - ten programmable IDCs
• Built-in digital alarm communicator/transmitter (DACT).
• Four Class B (Style Y) notification appliance circuits
(NACs) programmable for the following:
- ADA compliant strobe synchronization
- Selective silence (horn/strobe mute)
- Temporal or steady signal
- Silenceable or non-silenceable
- Auto-silence and silence inhibit
• Three programmable Form-C relays.
• 24 VDC special application power outputs (resettable
and non-resettable).
• Optional Class A converter module for NACs and IDCs
(model CAC-5X).
• Optional transmitter module for municipal box service
and reverse polarity (model 4XTMF).
• Completely field programmable at keypad
- does not require special software or extra equipment
- two password protected programming levels
• 80-character, backlit, high-angle, LCD display.
continued on next page
SIGNALING
i ^3™ is a trademark of Honeywell International Inc.
UL^® is a registered trademark of Underwriter’s Laboratories Inc.
S1869
FM _MEA
Reference Certificate
APPROVED Approved
of Compliance
7165-1703:0166 VMA-45894-02C
(Revision 1)
GAMEWELL-FCI
12 Clintonville Road, Northford, CT 06472-1610 USA • Tel: [phone] • Fax: [phone]
Specifications are for information only, are not intended for installation purposes, and are subject to change without notice. No responsibility is assumed by Gamewell-FCI for their use.
©2013 by Honeywell International Inc. All rights reserved.
www.gamewell-fci.com
9021-60293 Rev. C page 1 of 2