DACT-E3_15 Datasheet, PDF (1/1 Pages) Gamewell-FCI by Honeywell – Digital Alarm Communicator Transmitter

DACT-E3
Description
The Digital Alarm Communicator Transmitter (DACT-E3) is
a digital communications circuit. It is an optional compo-
nent of the following systems.
• E3 Series^® Expandable Emergency Evacuation System
• S3 Series Small Addressable Fire Alarm Control Panel
The DACT-E3 sends digital signals over the telephone net-
work to a central station. This module can be located in the
main cabinet or remotely located via a local RS-485 serial
interface.
The DACT-E3 is compatible with digital alarm communica-
tor receivers (DACRs) that receive the following signaling
formats:
• SIA DC8
• 3+1 2300 Hz
• SIA DCS20
• 4+2 1400 Hz
• Ademco Contact ID
• 4+2 2300 Hz
• 3+1 1400 Hz
In addition to the DACT-E3 being compatible with digital
signaling formats, the DACT-E3 features numerous for-
mats for communication to a central station. As a digital
communicator, the DACT-E3 complies with FCC Part 8,
Telecommunication Standards for DC and AC Ringer
Equivalence.
Installation Instructions
The DACT-E3 is adaptable for installation in standard E3
Series and S3 Series System cabinets. Typically, the
DACT-E3 module mounts on standoffs on top of the left
side of the ILI-MB-E3/ILI95-MB-E3 or SLP (Smart Loop
Panel) module. Either unit can be easily connected to the
backbox or sub-assembly plate depending on the cabinet
module.
Note: For instructions on installing the DACT-E3, refer to
the following documents:
• E3 Series Expandable Emergency Evacuation Manual,
P/N:LS10080-051GF-E
• DACT-E3 Installation Instructions, P/N:9000-0581
• S3 Series (Small Addressable Fire Alarm Control
Panel) UL Listing Document, P/N:LS10005-051GF-E
Specifications
Operating Voltage:
24 VDC (from the PM-9/PM-9G
power supply)
Operating Current:
0.018 amp
Alarm Current:
0.018 amp
Operating Temperature: 32° to 120° F (0 to 49° C)
Relative Humidity:
0 to 93%, non-condensing at
90° F (32° C)
E3 Series^® and NetSOLO^® are registered trademarks of Honeywell International Inc.
UL^® is a registered trademark of Underwriters Laboratories Inc.
Digital Alarm Communicator Transmitter
Features
DACT-E3
• Listed under UL^® Standard 864, 9th Edition.
• Communicates with the E3 Series, ILI-MB-E3/ILI95-MB-
E3 or S3 Series SLP sub-assembly via RS-485.
• Transmits in a variety of formats (including full
Contact ID).
• Transmits and verifies data to the central station.
• Offers pre-programmed dialing to the central station
phone number.
• Performs on and off-hook status to the phone lines.
• Traces proper central station “ACK” and “Kiss-off” tone.
• Activates hang-up and release phone lines.
• Compatible with the IPDACT Internet Communicator.
Ordering Information
Part Number Description
DACT-E3
Digital alarm communicator transmitter
SIGNALING
S1869
FM _MEA
City of
Chicago _{City of}
APPROVED Approved
Approved Denver
3025415 FDNY: 7165-1703:0125 ^Class1 Approved
COA #6077
Class2
High Rise
GAMEWELL-FCI
12 Clintonville Road, Northford, CT 06472-1610 USA • Tel: [phone] • Fax: [phone]
Specifications are for information only, are not intended for installation purposes, and are subject to change without notice. No responsibility is assumed by Gamewell-FCI for their use.
©2015 by Honeywell International Inc. All rights reserved.
www.gamewell-fci.com
9020-0610 Rev. K page 1 of 1