|
B200SR Datasheet, PDF (1/1 Pages) Gamewell-FCI by Honeywell – Sensor Sounder Base | |||
|
B200SR
Description
â¢
The B200SR Series sounder base sets a new standard for
performance, installation, and aesthetics. It is a non-
addressable base that is available in both Velociti® and
Clip⢠protocols. The B200SR is designed for new and
existing dwelling unit applications. It offers maximum flexi-
bility in installation, configuration, and operation to comply
or exceed the UL® Standard 268 and UL® Standard 464
requirements.
The B200SR is fully compatible and is a replacement for
the existing B501BH-Series sounder base installations. By
removing a jumper, the device enables users to select one
of two B501-supported tones (ANSI Temporal 3 or Contin-
uous).
â¢
With its attractive aesthetics, the B200SR is ideal for use
with applications where appearance is critical. For exam-
ple, the sounder base employs a separate mounting plate
that installs on various junction box sizes to eliminate
unsightly surface-mount boxes (refer to Table 1). In addi-
tion, the mounting plate enables pre-wiring of all connec-
tions to simplify the installation. To install the housing, use
the mounting plate, and secure two retaining screws to
lock-it in position. The retaining screws are covered by the
installed sensor head for added tamper resistance.
Specifications
Physical Specifications
Base Diameter:
6.875â (17.5 cm)
Base Height:
Shipping Weight:
2.0â (5.08 cm) less sensor
0.50 lb. (227 gm)
Operating
Temperature Range: 32° to 120° F (0° to 49° C)
Operating Humidity 10% to 93% relative humidity
Range:
(non-condensing)
â¢
Electrical Specifications
External Supply
Voltage:
16 to 33 VDC (VFWR)
Standby Current:
500 µA maximum
Alarm Current:
35 mA maximum
SLC Operating Voltage: 15 to 32 VDC
SLC Standby Current: 300 µA maximum
Sound Output:
Greater than 85 dBA minimum â
measured in a UL reverberant
room at 10 ft. 24 Volts (in contin-
uous tone).
â¢
â¢
Table 1: B200SR Junction Box Selection Guide
Single
Gange
3.5â
4.0â
Octagonal Octagonal
4.0â
Square
4.0â Square w/
3.0â mud ring
Yes
Yes
Yes
Yes
Yes
50 mm
60 mm
70 mm
75 mm
No
No
Yes
No
â¢UL® is a registered trademark of Underwriters Laboratories Inc.
Sensor Sounder Base
B200SR
Features
⢠Complies with UL® Standard 268 and UL® Standard
464.
⢠Provides a tone selection via an onboard jumper.
⢠Offers a pre-wire mounting plate that fits various
junction box sizes.
⢠Includes a mechanical locking feature that prevents the
removal of the attached sensor head.
⢠Fully compatible with the existing B501BH-Series
sounder base installations.
Ordering Information
Part Number Description
B200SR
Sensor Sounder Base
Note: Use the B200SR with the 7100 Series, 602 Series
or Gamewell and FCI (Legacy) panels.
GAMEWELL-FCI
12 Clintonville Road, Northford, CT 06472-1610 USA ⢠Tel: (203) 484-7161 ⢠Fax: (203) 484-7118
Specifications are for information only, are not intended for installation purposes, and are subject to change without notice. No responsibility is assumed by Gamewell-FCI for their use.
©2014 by Honeywell International Inc. All rights reserved.
www.gamewell-fci.com
9021-60553 Rev. D page 1 of 1
|