7200-B-RETROFIT Datasheet, PDF (1/2 Pages) Gamewell-FCI by Honeywell – Retrofit Kits FCI 7200 to E3 Series

7200 Retrofit Kits
Description
The Gamewell-FCI,7200 Retrofit Kits provide a simple way
to convert the existing 7200 CAB B and CAB C systems to
the new state-of-the-art E3 Series^® fire alarm control panel.
The Retrofit Kits offer a cost-effective solution to upgrade
the FCI 7200 legacy panels without replacing the existing
backbox secured on the wall. This solution eliminates the
expensive cost of repairing walls, buying new cabinets or
replacing the existing FCI 7200 backbox.
All retrofit kits provide backplates that mount directly into
the FCI 7200 backbox. Each backplate includes mounting
patterns to allow an easy installation of the E3 Series
plates and sub-assemblies. A new inner door includes slots
for the following components:
• LCD-E3 panel display • Addressable switch buttons
• LED drivers
• Paging microphone
• LCD-SLP LCD touchscreen display
The black outer door completes the kit with new locks.
The FCI 7200 KDU remote annunciator plate is an add-on
option for the Retrofit Kits. This retrofit option allows you to
reuse the existing backbox to retrofit the FCI 7200's KDU
remote annunciators to accommodate an E3 Series sup-
ported annunciator.
Retrofitting is a cost-effective way to upgrade your facilities'
fire alarm control panel without swapping out smoke detec-
tors and notification devices. Upgrading your legacy FCI
7200 System to the Gamewell-FCI, E3 Series System con-
verts your fire alarm system, so that it is compliant with the
most current UL^® and NFPA codes and standards.
Installation
To retrofit from a FCI 7200 panel to an E3 Series System,
refer to the following time-saving steps which can save a
lot in setup and labor costs.
1. Remove all field wiring from the 7200 sub-assemblies
that are installed inside the cabinet.
Note: GW-FCI recommends labeling all wiring that is
removed for quicker terminating.
2. Unscrew the 7200 mounting plate from the backbox
and remove sub-assemblies.
3. Remove the 7200 front door.
4. Install the new retrofit mounting plate for E3 Series-
sub-assemblies or plates.
5. Install the new E3 Series panels and connect with the
existing wiring.
6. Auto configure the system or custom program the E3
Series.
UE3L^{®Seisrieasr®}egaisntderSedysttreamdeSmeanrskoor^®f Uanrdeerrewgriistetersre’ LdatbraodraetmoraierkssInocf .Honeywell ^{International Inc.}
Retrofit Kits
FCI 7200 to E3 Series^®
7200-C-RETROFIT
Features
• Listed under UL^® Standard 864, 9th Edition.
• Offers a cost-effective solution for upgrading an existing
system without buying a complete fire alarm system.
• Upgrades to the state-of-the-art E3 Series fire alarm
and mass notification system.
• Includes a simple plate system for easy installation.
• Allows the existing cabinet to remain mounted on the
wall.
• Reuses the existing System Sensor^® CLIP detectors/
modules, and notification appliance devices.
• Provides the option of the KDU remote annunciator
retrofit.
E3 Series Features
For additional information on the E3 Series features, refer
to the E3 Series Data Sheet Part Number: 9020-0637.
SIGNALING
S1869
GAMEWELL-FCI
12 Clintonville Road, Northford, CT 06472-1610 USA • Tel: [phone] • Fax: [phone]
Specifications are for information only, are not intended for installation purposes, and are subject to change without notice. No responsibility is assumed by Gamewell-FCI for their use.
©2014 by Honeywell International Inc. All rights reserved.
www.gamewell-fci.com
9021-60733 Rev. D page 1 of 2