7MBP200VDA060-50 Datasheet, PDF (2/11 Pages) Fuji Electric – IGBT MODULE (V series) 600V / 200A / IPM

7MBP200VDA060-50
IGBT Modules
http://www.fujielectric.com/products/semiconductor/
Electrical Characteristics (Tj=25ºC, VCC=15V unless otherwise specified)
Items
Collector Current at off signal input
Collector-Emitter saturation voltage
Forward voltage of FWD
Collector Current at off signal input
Collector-Emitter saturation voltage
Forward voltage of FWD
Switching time
Symbol
ICES
VCE(sat)
VF
ICES
VCE(sat)
VF
ton
toff
trr
Conditions
VCE=600V
IC=200A
IF=200A
VCE=600V
IC=100A
IC=100A
Terminal
Chip
Terminal
Chip
Terminal
Chip
Terminal
Chip
VDC=300V, Tj=125ºC, IC=200A
VDC=300V, IC=200A
Supply current of P-side pre-driver (per one unit)
Iccp
Supply current of N-side pre-driver
Iccn
Input signal threshold voltage
Vinth(on)
Vinth(off)
Over Current Protection
Level
Inverter
Brake
IOC
Over Current Protection Delay time
tdOC
Short Circuit Protection Delay time
tSC
IGBT Chips Over Heating Protection Temperature Level TjOH
Over Heating Protection Hysteresis
TjH
Under Voltage Protection Level
VUV
Under Voltage Protection Hysteresis
VH
tALM(OC)
Alarm Signal Hold Time
tALM(UV)
tALM(TjOH)
Resistance for current limit
RALM
Switching Frequency= 0-15kHz
TC=-20~110ºC
Vin-GND
ON
OFF
Tj=125ºC
Tj=125ºC
Tj=125ºC
Surface of IGBT Chips
ALM-GND
TC=-20~110ºC
VCC
10V
Min.
-
-
-
-
-
-
-
-
-
-
1.1
-
-
-
-
1.2
1.5
300
150
-
-
150
-
11.0
0.2
1.0
2.5
5.0
960
Typ.
-
-
1.40
-
1.80
-
-
1.45
-
2.00
-
-
-
-
-
1.4
1.7
-
-
5
2
-
20
-
0.5
2.0
4.0
8.0
1265
Max.
1.0
2.35
-
2.70
-
1.0
2.05
-
2.40
-
-
2.1
0.3
24
93
1.6
1.9
-
-
-
3
-
-
12.5
-
2.4
4.9
11.0
1570
Units
mA
V
V
V
V
mA
V
V
V
V
µs
µs
µs
mA
mA
V
V
A
A
µs
µs
ºC
ºC
V
V
ms
ms
ms
Ω
Thermal Characteristics (TC = 25ºC)
Items
Junction to Case Thermal Resistance (*10)
Inverter
Brake
Case to Fin Thermal Resistance with Compound
IGBT
FWD
IGBT
FWD
Note *10: For 1device, the measurement point of the case is just under the chip.
Symbol
Rth(j-c)Q
Rth(j-c)D
Rth(j-c)Q
Rth(j-c)D
Rth(c-f)
Noise Immunity (VDC=300V, VCC=15V)
Items
Conditions
Common mode rectangular noise
Pulse width 1μs, polarity ±, 10 min.
Judge : no over-current, no miss operating
Min.
-
-
-
-
-
Min.
±2.0
Typ.
-
-
-
-
0.05
Typ.
-
Max.
0.27
0.46
0.47
0.90
-
Max.
-
Units
°C/W
°C/W
°C/W
°C/W
°C/W
Units
kV
Recommended Operating Conditions
Items
Symbol
DC Bus Voltage
VDC
Power Supply Voltage of Pre-Driver
VCC
Switching frequency of IPM
fSW
Arm shoot through blocking time for IPM's input signal tdead
Screw Torque (M4)
-
Min.
Typ.
Max.
Units
-
-
400
V
13.5
15.0
16.5
V
-
-
20
kHz
1.0
-
-
µs
1.3
-
1.7
Nm
2