6MBP50VBA060-50 Datasheet, PDF (2/8 Pages) Fuji Electric – IGBT MODULE (V series) 600V / 50A / IPM

6MBP50VBA060-50
IGBT Modules
http://www.fujielectric.com/products/semiconductor/
Electrical Characteristics (Tj=25ºC, VCC=15V unless otherwise specified)
Items
Collector Current at off signal input
Collector-Emitter saturation voltage
Symbol
ICES
VCE(sat)
Forward voltage of FWD
VF
ton
Switching time
toff
trr
Supply current of P-side pre-driver (per one unit)
Iccp
Supply current of N-side pre-driver
Iccn
Input signal threshold voltage
Vinth(on)
Vinth(off)
Over Current Protection Level
IOC
Over Current Protection Delay time
tdOC
Short Circuit Protection Delay time
tSC
IGBT Chips Over Heating Protection Temperature Level TjOH
Over Heating Protection Hysteresis
TjH
Under Voltage Protection Level
VUV
Under Voltage Protection Hysteresis
VH
tALM(OC)
Alarm Signal Hold Time
tALM(UV)
tALM(TjOH)
Resistance for current limit
RALM
Conditions
VCE=600V
IC=50A
Terminal
Chip
IF=50A
Terminal
Chip
VDC=300V, Tj=125ºC
Ic=50A
VDC=300V
IF=50A
Switching Frequency= 0-15kHz
Tc=-20~110ºC
Vin-GND
Tj=125ºC
ON
OFF
Tj=125ºC
Tj=125ºC
Surface of IGBT Chips
ALM-GND
Tc=-20~110ºC
VCC
10V
Min.
-
-
-
-
-
1.1
-
-
-
-
1.2
1.5
75
-
-
150
-
11.0
0.2
1.0
2.5
5.0
960
Typ.
-
-
1.40
-
1.80
-
-
-
-
-
1.4
1.7
-
5
2
-
20
-
0.5
2.0
4.0
8.0
1265
Max.
1.0
2.00
-
2.30
-
-
2.1
0.3
11
34
1.6
1.9
-
-
3
-
-
12.5
-
2.4
4.9
11.0
1570
Units
mA
V
V
V
V
µs
µs
µs
mA
mA
V
V
A
µs
µs
ºC
ºC
V
V
ms
ms
ms
Ω
Thermal Characteristics (TC = 25ºC)
Items
Junction to Case Thermal Resistance (*10)
Inverter
IGBT
FWD
Case to Fin Thermal Resistance with Compound
Note *10: For 1device, the measurement point of the case is just under the chip.
Symbol
Rth(j-c)Q
Rth(j-c)D
Rth(c-f)
Noise Immunity (VDC=300V, VCC=15V)
Items
Conditions
Common mode rectangular noise
Pulse width 1μs, polarity ±, 10 minute
Judge : no over-current, no miss operating
Min.
-
-
-
Min.
±2.0
Typ.
-
-
0.05
Typ.
-
Max.
0.74
1.27
-
Max.
-
Units
°C/W
°C/W
°C/W
Units
kV
Recommended Operating Conditions
Items
Symbol
DC Bus Voltage
VDC
Power Supply Voltage of Pre-Driver
VCC
Arm shoot through blocking time for IPM's input signal tdead
Screw Torque (M4)
-
Min.
Typ.
Max.
Units
-
-
400
V
13.5
15.0
16.5
V
1.0
-
-
µs
1.3
-
1.7
Nm
2