FT2232H_12 Datasheet, PDF (1/67 Pages) Future Technology Devices International Ltd. – Dual High Speed USB to Multipurpose UART/FIFO IC

Document No.: FT_000061
FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC
Version 2.21
Clearance No.: FTDI#77
Future Technology
Devices International Ltd
FT2232H Dual High Speed
USB to Multipurpose
UART/FIFO IC
The FT2232H is FTDI‟s 5^th generation of USB ^
devices. The FT2232H is a USB 2.0 High
Speed (480Mb/s) to UART/FIFO IC. It has the _
capability of being configured in a variety of
industry standard serial or parallel interfaces.
The FT2232H has the following advanced
features:

 Single chip USB to dual serial / parallel ports
with a variety of configurations.

 Entire USB protocol handled on the chip. No
USB specific firmware programming required. _
 USB 2.0 High Speed (480Mbits/Second) and
Full Speed (12Mbits/Second) compatible.

 Dual Multi-Protocol Synchronous Serial Engine
(MPSSE) to simplify synchronous serial protocol _
(USB to JTAG, I²C, SPI or bit-bang) design.
 Dual independent UART or FIFO or MPSSE
ports.

 Independent Baud rate generators.
 RS232/RS422/RS485 UART Transfer Data Rate _
up to 12Mbaud. (RS232 Data Rate limited by _
external level shifter).
 USB to parallel FIFO transfer data rate up to 8 _
Mbyte/Sec.

 Single channel synchronous FIFO mode for
transfers upto 40 Mbytes/Sec

 CPU-style FIFO interface mode simplifies CPU
interface design.

 MCU host bus emulation mode configuration
option.

 Fast Opto-Isolated serial interface option.
 FTDI‟s royalty-free Virtual Com Port (VCP) and _
Direct (D2XX) drivers eliminate the _
requirement for USB driver development in
most cases.
 Adjustable receive buffer timeout.
 Option for transmit and receive LED drive
signals on each channel.
 Enhanced bit-bang Mode interface option with
RD# and WR# strobes
FT245B-style FIFO interface option with bi-
directional data bus and simple 4 wire
handshake interface.
Highly integrated design includes +1.8V LDO
regulator for VCORE, integrated POR function
and on chip clock multiplier PLL (12MHz –
480MHz).
Asynchronous serial UART interface option with
full hardware handshaking and modem
interface signals.
Fully assisted hardware or X-On / X-Off
software handshaking.
UART Interface supports 7/8 bit data, 1/2 stop
bits, and Odd/Even/Mark/Space/No Parity.
Auto-transmit enable control for RS485 serial
applications using TXDEN pin.
Operational configuration mode and USB
Description strings configurable in external
EEPROM over the USB interface.
Configurable I/O drive strength (4, 8, 12 or
16mA) and slew rate.
Low operating and USB suspend current.
Supports bus powered, self powered and high-
power bus powered USB configurations.
UHCI/OHCI/EHCI host controller compatible.
USB Bulk data transfer mode (512 byte packets
in High Speed mode).
+1.8V (chip core) and +3.3V I/O interfacing
(+5V Tolerant).
Extended -40°C to 85°C industrial operating
temperature range.
Compact 64-LD Lead Free LQFP or QFN
package
+3.3V single supply operating voltage range.
ESD protection for FT2232H IO‟s:
Human Body Model (HBM) ±2kV,
Machine Mode (MM) ±200V,
Charge Device Model (CDM) ±500V,
Latch-up free.
Neither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or reproduced in any material or
electronic form without the prior written consent of the copyright holder. This product and its documentation are supplied on an as-is basis and no warranty as
to their suitability for any particular purpose is either made or implied. Future Technology Devices International Ltd will not accept any claim for damages
Copyright © 2012 Future Technology Devices International Limited
1