FSP850-50AAG_15 Datasheet, PDF (1/1 Pages) FSP TECHNOLOGY INC. – industrial level of switching power

IPC PSU
FSP850-50AAG
DE SC RIP TIO N
FSP800-50AAG is an industrial level of switching power
supply. The power supply comes to offer the total power
capacity up to 850 Watts, and uses unique active PFC
(Power Factor C orrection) circuit design with its high-load
electrical components, makes it to be perfectly used in an
industrial environment. In addition, with its full range of
input and output electrical features, the power supply is
ideally the best choice for server, workstation,
communication or any other automation applications to
use. The product also complies with the latest safety and
EMC standards, which is perfectly to meet various
regulations worldwide.
AP P L IC ATIO N
For standard, advanced workstation, server and industrial
power system.
FEATURES
85 Plus Gold
Low Ripple & Noise
Output over voltage protection
Short circuit protection on all outputs
Resettable power shut down
INTERNAL 4 cm fan 100% burn-in under high ambient
temperature(50℃)
Vacuum-impregnated transformer
MTBF:100K hours at 25℃
100% Hi-pot tested Line input fuse protection
W ATTAGE
Wa tta g e :
850W
DIMENSION
Dimension:
190mm(L) x 150mm(W) x
86mm(H)
PRODUCT HIGHLIGHT
Efficiency Level:
80 Plus Gold
Altitude:
5000M
INPUT SPECIFICATION
Input Range:
90-264 Vac
Input Frequency: 47-63 Hz
Input Current:
115V@ 12.0 Amps-rms maximum
230V@ 6.0 Amps-rms maximum
GENERAL SPECIFICATION
Effciency:
90% 230VAC
Vo lta g e
+3.3V, +12V, +5V, +5SB: ±5%
Re g ula tio n:
-12V: ±10%
*Output Voltage and C urrent Rating
+3.3V
Ripple-Noise(R-P) mV
50mV
Regulation Load %
±5%
Output Max.(A)
25A
Output Min.(A)
0A
+5V
50mV
±5%
25A
0.1A
SAFETY STANDARD APPAOVAL
OUTPUT SPECIFICATION
Hold up Time:
Ouput Voltage
Re g ula tio n:
Output Rise Time:
Ripple & Noise:
115V/60Hz 17mSec.
Minimum@100% Load,
230V/50Hz 17mSec.
Minimum,@100% Load
+3.3Vdc output : +3.76 Vdc
minimum, + 4.8Vdc
maximum
+5Vdc output : +5.75 Vdc
minimum, + 7.0Vdc
maximum
+12Vdc output : +13.5 Vdc
minimum, + 15.5Vdc
maximum
115V-rms/230V-rms 5V
20ms Maximum
115V-rms/230V-rms 12V
20ms Maximum
3.3V:50mV p-p
5V:50mV p-p
12V1:120mV p-p
-12V:120mV p-p
5Vsb:50mV p-p
ENVIRONMENTAL SPECIFICATION
T E MP.Ra ng e :
Storage Temperature: -
20°C to + 80℃
MT BF :
The power supply have a
minimum predicted
MTBF(MIL-HDBK-217) of
100,000 hours of continuous
operation at 25℃,
maximum-output load, and
nominal AC inout voltage
+12V1
120mV
±5%
70A
0.2A
-12V
120mV
±10%
0.5A
0A
+5Vsb
50mV
±5%
3.5A
0A
NO TE S
Maximum continuous total DC output power should not exceed 850W.
Maximum continuous combined load on +3.3DC and +5VDC outputs shall not exceed 125W.
Ripple and noise measurements shall be made under all specified load conditions through a single pole low pass filter
with 20MHz cutoff frequency. Outputs shall bypassed at the connector with a 0.1uF ceramic disk capacitor and a 10uF
electrolytic capacitor to simulate system loading.
This content is subject to change, please refer to specification for m ore detail.
FSP reserve the right to change the content without prior notice