FSP400-60UAP_15 Datasheet, PDF (1/1 Pages) FSP TECHNOLOGY INC. – industrial level of switching power

IPC PSU
FSP400-60UAP
DE SC RIP TIO N
FSP400-60UAP is an industrial level of switching power
supply. The power supply comes to offer the total power
capacity up to 400 Watts, and uses unique active PFC
(Power Factor C orrection) circuit design with its high-load
electrical components, makes it to be perfectly used in an
industrial environment. In addition, with its full range of
input and output electrical features, the power supply is
ideally the best choice for server, workstation,
communication or any other automation applications to
use. The product also complies with the latest safety and
EMC standards, which is perfectly to meet various
regulations worldwide.
SAFETY STANDARD APPAOVAL
AP P L IC ATIO N
For standard, advanced server, NAS, storage, and
industrial power system.
FEATURES
80 Plus Platinum
Low Ripple & Noise
Output over voltage protection
Short circuit protection on all outputs
Resettable power shut down
INTERNAL 4 cm fan
Two +12V output (+12V/1,+12V/2)
100% burn-in under high ambient temperature(50℃)
Vacuum-impregnated transformer
MTBF:100K hours at 25℃
100% Hi-pot tested
Line input fuse protection
W ATTAGE
Wa tta g e :
400W
DIMENSION
Dimension:
190mm(L) x 100mm(W) x
40.5mm(H)
PRODUCT HIGHLIGHT
Efficiency Level:
80 Plus Platinum
Altitude:
5000M
INPUT SPECIFICATION
Input Range:
90-264 Vac
Input Frequency: 47-63 Hz
Input Current:
115V@ 6.3 Amps-rms maximum
230V@ 3.0 Amps-rms maximum
OUTPUT SPECIFICATION
Hold up Time:
Ouput Voltage
Re g ula tio n:
Output Rise Time:
Ripple & Noise:
115V/60Hz 12mSec.
Minimum@100% Load,
230V/50Hz 16mSec.
Minimum,@100% Load
+3.3Vdc output : +3.5 Vdc
minimum, + 4.8Vdc
maximum
+5Vdc output : +5.5 Vdc
minimum, + 7Vdc maximum
+12Vdc output : +13.4 Vdc
minimum, + 16Vdc
maximum
115V-rms/230V-rms 5V
20ms Maximum
3.3V:50mV p-p
5V:50mV p-p
12V1:120mV p-p
12V2:120mV p-p
-12V:120mV p-p
5Vsb:50mV p-p
ENVIRONMENTAL SPECIFICATION
T E MP.Ra ng e :
Storage Temperature: -
20°C to + 80℃
MT BF :
The power supply have a
minimum predicted
MTBF(MIL-HDBK-217) of
100,000 hours of continuous
operation at 25℃,
maximum-output load, and
nominal AC inout voltage
GENERAL SPECIFICATION
Effciency:
92% 230VAC
Vo lta g e
+3.3V, +12V, +5V, +5VSB: ±5%
Re g ula tio n:
-12V, -5V: ±10%
*Output Voltage and C urrent Rating
+3.3V
Ripple-Noise(R-P) mV 50mV
Regulation Load %
±5%
Output Max.(A)
16A
Output Min.(A)
0.3A
+5V
50mV
±5%
18A
0.3A
+12V1
120mV
±5%
18A
0.5A
+12V2
120mV
±5%
18A
0.5A
-12V
120mV
±10%
0.5A
0A
+5Vsb
50mV
±5%
3A
0A
NO TE S
C ombined 3.3V and 5 power shall not exceed 110W.
Ripple and noise measurements shall be made under all specified load conditions through a single pole low pass filter
with 20MHz cutoff frequency
Outputs shall bypassed at the connector with a 0.1uF ceramic disk capacitor and a 47uF electrolytic capacitor to
simulate system loading.
Maximum continuous total DC output power should not exceed 400W
This content is subject to change, please refer to specification for m ore detail.
FSP reserve the right to change the content without prior notice