FSP400-20FBGB_15 Datasheet, PDF (1/1 Pages) FSP TECHNOLOGY INC. – industrial level of switching power

IPC PSU
FSP400-20FBGB
DE SC RIP TIO N
FSP400-20FBGB is an industrial level of switching power
supply. The power supply comes to offer the total power
capacity up to 400 Watts, and uses unique active PFC
(Power Factor C orrection) circuit design with its high-load
electrical components, makes it to be perfectly used in an
industrial environment. In addition, with its full range of
input and output electrical features, the power supply is
ideally the best choice for server, workstation,
communication or any other automation applications to
use. The product also complies with the latest safety and
EMC standards, which is perfectly to meet various
regulations worldwide.
AP P L IC ATIO N
For standard, advanced server, NAS and industrial power
system.
FEATURES
80 Plus Gold
Low Ripple & Noise
Output over voltage protection
Short circuit protection on all outputs
Resettable power shut down
INTERNAL 4 cm fan
100% burn-in under high ambient temperature(50℃)
Vacuum-impregnated transformer
MTBF:100K hours at 25℃
100% Hi-pot tested
Line input fuse protection
W ATTAGE
Wa tta g e :
400W
DIMENSION
Dimension:
190mm(L) x 81.5mm(W) x
40.5mm(H)
PRODUCT HIGHLIGHT
Efficiency Level:
80 Plus Gold
Altitude:
5000M
INPUT SPECIFICATION
Input Range:
90-264 Vac
Input Frequency: 47-63 Hz
Input Current:
115V@ 6.0 Amps-rms maximum
230V@ 3.0 Amps-rms maximum
GENERAL SPECIFICATION
Effciency:
92% 230VAC
Vo lta g e
+12V, +5SB: ±5%
Re g ula tio n:
PWOK Delay Time: 500ms > PWOK > 100ms
*Output Voltage and C urrent Rating
Ripple-Noise(R-P) mV
Regulation Load %
Output Max.(A)
Output Min.(A)
+12V1
120mV
±5%
32.1A
0A
SAFETY STANDARD APPAOVAL
OUTPUT SPECIFICATION
Hold up Time:
Ouput Voltage
Re g ula tio n:
Output Rise Time:
Ripple & Noise:
115V/60Hz 16mSec.
Minimum@100% Load,
230V/50Hz 16mSec.
Minimum,@100% Load
+12Vdc output : +13.3 Vdc
minimum, + 15.5Vdc
maximum
115V-rms/230V-rms 12V
20ms Maximum
12V1:120mV p-p
5Vsb:50mV p-p
ENVIRONMENTAL SPECIFICATION
T E MP.Ra ng e :
Storage Temperature: -
20°C to + 80℃
MT BF :
The power supply have a
minimum predicted
MTBF(MIL-HDBK-217) of
100,000 hours of continuous
operation at 25℃,
maximum-output load, and
nominal AC inout voltage
+5Vsb
50mV
±5%
3A
0A
NO TE S
No load condition-No damage or hazardous condition should occur with all the DC output connectors disconnected from
the load. The power supply may latch into the shutdown state.
The +12V and +5VSB total output shall not exceed 400 watts. Ripple and noise measurements shall be made under all
specified load conditions through a single pole low pass filter with 20MHz cutoff frequency. Outputs shall bypassed at
the connector with a 0.1uF ceramic disk capacitor and a 10uF electrolytic capacitor to simulate system loading.
This content is subject to change, please refer to specification for m ore detail.
FSP reserve the right to change the content without prior notice