MC9RS08KA2FS Datasheet, PDF (2/2 Pages) Freescale Semiconductor, Inc – 8-bit Microcontrollers

Cost-Effective Development Tools
For more information on development tools,
please refer to the Freescale Development
Tool Selector Guide (SG1011)
DEMO9RS08KA2
$50*
Cost-effective demonstration board with
potentiometer, LEDs, serial port and built-in
USB-BDM cable for debugging
and programming
M68CYCLONEPROE
$499*
RS08/HC08/HCS08/HC12/HCS12 stand-
alone flash programmer or in-circuit emulator,
debug tool, flash programmer; USB, serial or
Ethernet interface options
USBMULTILINKBDME
$99*
Universal HCS08/RS08 in-circuit debug tool
and Flash programmer; USB PC interface
USBSPYDER08
$29*
Cost-effective USB debug tool for use with
8-pin PDIP package
CWX-H08-SE
Free**
CodeWarrior™ Special Edition for HC(S)08/
RS08 MCUs. Includes integrated development
environment (IDE), linker, debug tool, unlimited
assembler, Processor Expert™ auto-code
generator and full-chip simulation. 16 KB C
Compiler included for HC(S)08 MCUs.
*Prices indicated are MSRP
**Subject to license agreement and registration
Data Sheets
MC9RS08KA2
Data Sheet for KA2/KA1
Package Options
Part Number Package
MC9RS08KA2CDB 6-pin DFN
MC9RS08KA2CSC 8-pin SOIC-NB
MC9RS08KA2CPC 8-pin PDIP
MC9RS08KA1CDB 6-pin DFN
MC9RS08KA1CSC 8-pin SOIC-NB
MC9RS08KA1CPC 8-pin PDIP
Temp. Range
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
Flexible Clock Options
• Internal clock source module (ICS) contains
a frequency-locked loop (FLL) controlled by
internal reference
• Helps eliminate the cost of all external
clock components
• Reduces board space
• Increases system reliability
• Precision trimming of internal reference allows typical
0.1% resolution and +0.5% to -1% deviation over
operating temperature and voltage
• Provides one of the most accurate internal clock
sources on the market for the money
• Internal reference can be trimmed from 31.25 kHz to • Allows for trimming to adjust bus clock in
39.065 kHz, allowing for 8 MHz to 10 MHz FLL output
specific applications
Timer
• 8-bit modulo timer with 8-bit prescaler
• Generates periodic trigger for time-based software
loops using timer overflow interrupt
• Allows external timer clock source
• Utilizes TCLK input as event trigger; the timer can
be used as an 8-bit event counter
Analog Comparator
• Option to compare to internal reference
• Requires only a single pin for input signal
• Option to route comparator output directly to pin
• Allows other components in system to see result of
comparator with minimal delay
• Allows operation in MCU STOP mode
• Offers function to wake up the MCU from WAIT/STOP
Real-Time Interrupt
• Real-time interrupt trigger with 3-bit prescaler
• Allows periodic wake-up or software trigger with delay
ranging from 8 ms to 1.024s
• Built-in low power 1 kHz clock source
• Options to use low power 1 kHz internal clock to drive
the RTI
• Minimizes power consumption in MCU STOP
Four Bidirectional Input/Output (I/O) Lines; One Input-Only Line and One Output-Only Line
• Software selectable pull-ups on ports when used as
input (internal pull-up on RESET)
• Eliminates need for external resistors to help reduce
customer system cost
• Software selectable slew rate control on ports when
used on output
• Configures ports for slower slew rate to help minimize
noise emissions from the MCU
• 5-pin keyboard interrupt module with software
selectable polarity on edge or edge/level modes
• Helps to virtually eliminate external glue logic when
interfacing to simple keypads using keyboard scan with
programmable pull-up/pull-down functionality
System Protection
• Watchdog computer operating properly (COP) reset
with option to run from dedicated 1 kHz internal clock
source or bus clock
• Resets device in instance of runaway or corrupted code
• Helps protect in case of clock loss with independent
clock source
• Low-voltage detection with reset or interrupt
• Allows system to write/save important variables before
voltage drops to low
• Holds devices in reset until reliable voltage levels are
reapplied to the part
• Illegal opcode and illegal address detection with reset • Resets device in instance of runaway or corrupted code
• Security feature for flash memory
• Helps prevent unauthorized access to memory to
protect valuable software intellectual property
Background Debugging System
• On-chip BDM
• Provides single-wire debugging and emulation interface
• Eliminates need for expensive emulation tools
• Provides circuit emulation without the need for
additional, expensive development hardware
Learn More: ^{For more information about Freescale,}
please visit www.freescale.com.
Freescale and the Freescale logo are trademarks or registered trademarks of Freescale Semiconductor, Inc.
in the U.S. and other countries. All other product or service names are the property of their respective owners.
© Freescale Semiconductor, Inc. 2008.
Document Number: MC9RS08KA2FS
REV 0