P1010 Datasheet, PDF (1/2 Pages) Freescale Semiconductor, Inc – P1010 and P1014 low-power communications processors

QorIQ Communications Platforms
P1 Series
P1010 and P1014 low-power communications processors
Freescale QorIQ communications platforms
are the next-generation evolution of our
leading PowerQUICC communications
processors. Built using high-performance
Power Architecture^® cores, QorIQ platforms
enable a new era of networking innovation
where the reliability, security and quality of
service for every connection matters.
QorIQ P1010 and P1014
Communications Processors
The QorIQ P1 platform series, which includes
the P1010 and P1014 communications
processors, offers the value of extensive
integration and extreme power smarts for
a wide variety of applications in the cost-
sensitive networking, network attached
storage, digital video surveillance and industrial
segments. Based on 45 nm technology for
low power implementation, the P1010 and
P1014 processors provide a single-core,
low-power solution for the 533 MHz to
800 MHz performance range, along with a
trusted security platform and a rich set of
interfaces. The P1010 and P1014 processors
are perfectly suited for network attached
storage, digital video surveillance applications,
cost-sensitive Ethernet switch controllers and
industrial/factory automation applications with
demanding power/thermal constraints.
The QorIQ P1010 and P1014 processors are
pin compatible. The P1014 is a more nimble
derivative of the P1010 and targets the more
cost-sensitive applications with a lower power
envelop and sensible set of features. The
P1010 adds trusted architecture and CAN
controllers for additional versatility in the
industrial segments. Scaling from 533 MHz
to 800 MHz on a single core, the P1010 and
P1014 deliver an impressive performance for
the low end of the QorIQ portfolio.
The devices in these two platforms are
software compatible, sharing the e500
Power Architecture core and peripherals,
as well as being fully software compatible
with the existing PowerQUICC processors.
This enables you to create a product with
multiple performance points from a single
board design. The QorIQ P1010 single
core processor supports a trusted platform
architecture that enables an end to end
secure boot and code signing capability to
protect the integrity of your firmware and
prevent unauthorized use. Furthermore, CAN
interfaces allow ease of implementation of
industrial protocols and an easier fit into cost-
sensitive industrial applications.
The P1010 and P1014 processors have an
advanced set of features for ease of use.
The 256 KB L2 cache offers incremental
performance and enables the implementation
of software fast path drivers to enhance
networking performance for IP forwarding,
NAT firewall and IP sec and achieve line rate
on most usage cases. The integrated security
engine supports the cryptographic algorithms
commonly used in IPsec, SSL, 3GPP and other
networking and wireless security protocols.
The trusted architecture included in the P1010
provides additional platform security and
prevents unauthorized usage or intrusion.
The memory controller offers future-proofing
against memory technology migration with
support for low-power DDR3. It also supports
error correction codes, a baseline requirement
for any high-reliability system.
QorIQ P1010 and P1014 Block Diagram
Security
Acceleration
(Trusted Boot
on P1010 Only)
XOR
Power Architecture^®
e500 Core
32 KB
L1 I-Cache
32 KB
L1 D-Cache
256 KB
L2 Cache
Coherency Module
System Bus
DDR3/DDR3L SDRAM Controller
(16/32-bit for the P1010
16-bit only for the P1014)
2 x DUART, 2 X I²C, Timers,
Interrupt Control, SPI,
SD/MMC, GPIO
Flash Memory Controller (IFC)
TDM
USB 2.0/ 2 x
ULPI with FlexCAN
Integrated (P1010
PHY
only)
2x
SATA
3 x Gigabit
Ethernet
(2 x on
P1014)
On-Chip Network
2 x PCI Express^®
4-ch. DMA
Cores
6-lane SerDes