FSBM15SM60A Datasheet, PDF (8/16 Pages) Fairchild Semiconductor – SPM (Smart Power Module)

Electrical Characteristics (T_J = 25°C, Unless Otherwise Specified)
Control Part
Item
Quiescent V_CC Supply Cur-
rent
Quiescent V_BS Supply Cur-
rent
Fault Output Voltage
Short-Circuit Trip Level
Sensing Voltage
of IGBT Current
Supply Circuit Under-
Voltage Protection
Fault Output Pulse Width
ON Threshold Voltage
OFF Threshold Voltage
ON Threshold Voltage
OFF Threshold Voltage
Symbol
I_QCCL
I_QCCH
I_QBS
V_FOH
V_FOL
V_SC(ref)
V_SEN
UV_CCD
UV_CCR
UV_BSD
UV_BSR
t_FOD
V_IN(ON)
V_IN(OFF)
V_IN(ON)
V_IN(OFF)
Condition
V_CC = 15V
IN_{(UL, VL, WL)} = 5V
V_CC(L) - COM_(L)
V_CC = 15V
IN_{(UH, VH, WH)} = 5V
V_CC(UH), V_CC(VH), V_CC(WH) -
COM_(H)
V_BS = 15V
IN_{(UH, VH, WH)} = 5V
V_B(U) - V_S(U), V_B(V) -V_S(V),
V_B(W) - V_S(W)
V_SC = 0V, V_FO Circuit: 4.7kΩ to 5V Pull-up
V_SC = 1V, V_FO Circuit: 4.7kΩ to 5V Pull-up
V_CC = 15V (Note 5)
R_SC = 56 Ω, R_SU = R_SV = R_SW = 0 Ω and I_C = 22.5A
(Note Fig. 6)
Detection Level
Reset Level
Detection Level
Reset Level
C_FOD = 33nF (Note 6)
High-Side
Applied between IN_(UH), IN_(VH),
IN_(WH) - COM_(H)
Low-Side
Applied between IN_(UL), IN_(VL),
IN_(WL) - COM_(L)
Min. Typ. Max. Unit
-
- 26 mA
-
- 130 uA
-
- 420 uA
4.5 -
-V
-
- 1.1 V
0.45 0.51 0.56 V
0.45 0.51 0.56 V
11.5 12 12.5 V
12 12.5 13 V
7.3 9.0 10.8 V
8.6 10.3 12 V
1.4 1.8 2.0 ms
-
- 0.8 V
3.0 -
-V
-
- 0.8 V
3.0 -
-V
Note:
5. Short-circuit current protection is functioning only at the low-sides. It would be recommended that the value of the external sensing resistor (R_SC) should be
selected around 56 Ω in order to make the SC trip-level of about 22.5A at the shunt resistors (R_SU,R_SV,R_SW) of 0Ω . For the detailed information about the
6.
relationship between the external sensing
The fault-out pulse width t_FOD depends on
resistor (R_SC) and the
the capacitance value
shunt resistors (R_SU,R_SV,R_SW), please see Fig. 6.
of C_FOD according to the following approximate equation
:
C_FOD
=
18.3
x
10^-6
x
t_FOD[F]
Recommended Operating Conditions
Item
Supply Voltage
Control Supply Voltage
High-side Bias Voltage
Blanking Time for Preventing
Arm-short
PWM Input Signal
Input ON Threshold Voltage
Input OFF Threshold Voltage
Symbol
Condition
V_PN
V_CC
V_BS
t_dead
Applied between P - N_U, N_V, N_W
Applied between V_CC(UH), V_CC(VH), V_CC(WH) -
COM_(H), V_CC(L) - COM_(L)
Applied between V_B(U) - V_S(U), V_B(V) - V_S(V),
V_B(W) - V_S(W)
For Each Input Signal
f_PWM
V_IN(ON)
V_IN(OFF)
T_C ≤ 100°C, T_J ≤ 125°C
Applied between IN_(UH), IN_(VH), IN_(WH) -
COM_(H), IN_(UL), IN_(VL), IN_(WL) - COM_(L)
Applied between IN_(UH), IN_(VH), IN_(WH) -
COM_(H), IN_(UL), IN_(VL), IN_(WL) - COM_(L)
Values
Min. Typ. Max.
Unit
- 300 400 V
13.5 15 16.5 V
13.5 15 16.5 V
3
-
-
us
-
5
- kHz
0 ~ 0.65
V
4 ~ 5.5
V
©2003 Fairchild Semiconductor Corporation
Rev. E, August 2003