74LVT32374 Datasheet, PDF (4/6 Pages) Fairchild Semiconductor – Low Voltage 32-Bit D-Type Flip-Flop with 3-STATE Outputs

Absolute Maximum Ratings(Note 3)
Symbol
Parameter
V_CC
Supply Voltage
V_I
DC Input Voltage
V_O
DC Output Voltage
I_IK
DC Input Diode Current
I_OK
DC Output Diode Current
I_O
DC Output Current
I_CC
I_GND
T_STG
DC Supply Current per Supply Pin
DC Ground Current per Ground Pin
Storage Temperature
Value
−0.5 to +4.6
−0.5 to +7.0
−0.5 to +7.0
−0.5 to +7.0
−50
−50
64
128
±64
±128
−65 to +150
Recommended Operating Conditions
Conditions
Output in 3-STATE
Output in HIGH or LOW State (Note 4)
V_I < GND
V_O < GND
V_O > V_CC Output at HIGH State
V_O > V_CC Output at LOW State
Units
V
V
V
mA
mA
mA
mA
mA
°C
Symbol
Parameter
Min
Max
Units
V_CC
Supply Voltage
2.7
3.6
V
V_I
Input Voltage
0
5.5
V
I_OH
HIGH Level Output Current
−32
mA
I_OL
LOW Level Output Current
64
mA
T_A
Free-Air Operating Temperature
−40
85
°C
∆t/∆V
Input Edge Rate, V_IN = 0.8V–2.0V, V_CC = 3.0V
0
10
ns/V
Note 3: Absolute Maximum continuous ratings are those values beyond which damage to the device may occur. Exposure to these conditions or conditions
beyond those indicated may adversely affect device reliability. Functional operation under absolute maximum rated conditions is not implied.
Note 4: I_O Absolute Maximum Rating must be observed.
DC Electrical Characteristics
Symbol
Parameter
V_IK
Input Clamp Diode Voltage
V_IH
Input HIGH Voltage
V_IL
Input LOW Voltage
V_OH
Output HIGH Voltage
V_OL
Output LOW Voltage
I_I(HOLD)
(Note 5)
I_I(OD)
(Note 5)
I_I
Bushold Input Minimum Drive
Bushold Input Over-Drive
Current to Change State
Input Current
V_CC
(V)
2.7
2.7–3.6
2.7–3.6
2.7–3.6
2.7
3.0
2.7
2.7
3.0
3.0
3.0
3.0
3.0
3.6
Control Pins 3.6
Data Pins 3.6
I_OFF
I_PU/PD
I_OZL
I_OZH
I_OZH+
Power Off Leakage Current
Power Up/Down 3-STATE
Output Current
3-STATE Output Leakage Current
3-STATE Output Leakage Current
3-STATE Output Leakage Current
0
0–1.5V
3.6
3.6
3.6
T _A = −40°C to +85°C
Min
Max
−1.2
2.0
0.8
V_CC − 0.2
2.4
2.0
0.2
0.5
0.4
0.5
0.55
75
−75
500
−500
10
±1
−5
1
±100
±100
−5
5
10
Units
Conditions
V
I_I = −18 mA
V
V_O ≤ 0.1V or
V
V_O ≥ V_CC − 0.1V
I_OH = −100 µA
V
I_OH = −8 mA
I_OH = −32 mA
I_OL = 100 µA
I_OL = 24 mA
V
I_OL = 16 mA
I_OL = 32 mA
I_OL = 64 mA
µA
V_I = 0.8V
V_I = 2.0V
(Note 6)
µA
(Note 7)
V_I = 5.5V
µA
V_I = 0V or V_CC
V_I = 0V
V_I = V_CC
µA
0V ≤ V_I or V_O ≤ 5.5V
µA
V_O = 0.5V to 3.0V
V_I = GND or V_CC
µA
V_O = 0.5V
µA
V_O = 3.0V
µA
V_CC < V_O ≤ 5.5V
www.fairchildsemi.com
4