FST16211 Datasheet, PDF (3/8 Pages) Fairchild Semiconductor – 24-Bit Bus Switch

Absolute Maximum Ratings(Note 2)
Supply Voltage (V_CC)
DC Switch Voltage (V_S) (Note 3)
DC Input Voltage (V_IN) (Note 4)
DC Input Diode Current (l_IK) V_IN<0V
DC Output (I_OUT) Sink Current
DC V_CC/GND Current (I_CC/I_GND)
Storage Temperature Range (T_STG)
−0.5V to +7.0V
−0.5V to +7.0V
−0.5V to +7.0V
−50mA
128mA
+/− 100mA
−65°C to +150 °C
Recommended Operating
Conditions (Note 5)
Power Supply Operating (V_CC)
Input Voltage (V_IN)
Output Voltage (V_OUT)
Input Rise and Fall Time (t_r, t_f)
Switch Control Input
4.0V to 5.5V
0V to 5.5V
0V to 5.5V
0nS/V to 5nS/V
Switch I/O
0nS/V to DC
Free Air Operating Temperature (T_A) -40 °C to +85 °C
Note 2: The “Absolute Maximum Ratings” are those values beyond which
the safety of the device cannot be guaranteed. The device should not be
operated at these limits. The parametric values defined in the Electrical
Characteristics tables are not guaranteed at the absolute maximum rating.
The “Recommended Operating Conditions” table will define the conditions
for actual device operation.
Note 3: V_S is the voltage observed/applied at either A or B Ports across the
switch.
Note 4: The input and output negative voltage ratings may be exceeded if
the input and output diode current ratings are observed.
Note 5: Unused control inputs must be held HIGH or LOW. They may not
float.
DC Electrical Characteristics
Symbol
Parameter
V_CC
(V)
T_A = −40 °C to +85 °C
Min
Typ
Max
Units
(Note 6)
Conditions
V_IK
Clamp Diode Voltage
V_IH
HIGH Level Input Voltage
V_IL
LOW Level Input Voltage
I_I
Input Leakage Current
I_OZ
OFF-STATE Leakage Current
R_ON
Switch On Resistance
(Note 7)
I_CC
∆ I_CC
Quiescent Supply Current
Increase in I_CC per Input
4.5
4.0–5.5
2.0
4.0–5.5
5.5
0
5.5
4.5
4.5
4.5
4.0
5.5
5.5
Note 6: Typical values are at V_CC = 5.0V and T_A = +25°C
−1.2
V
I_IN = −18mA
V
0.8
V
±1.0
µA 0 ≤ V_IN ≤ 5.5V
10
µA V_IN = 5.5V
±1.0
µA 0 ≤ A, B ≤ V_CC
4
7
Ω
V_IN = 0V, I_IN = 64mA
4
7
Ω
V_IN = 0V, I_IN = 30mA
8
12
Ω
V_IN = 2.4V, I_IN = 15mA
11
20
Ω
V_IN = 2.4V, I_IN = 15mA
3
µA V_IN = V_CC or GND, I_OUT = 0
2.5
mA One input at 3.4V
Other inputs at V_CC or GND
Note 7: Measured by the voltage drop between A and B pins at the indicated current through the switch. On resistance is determined by the lower of the
voltages on the two (A or B) pins.
3
www.fairchildsemi.com