DM100 Datasheet, PDF (1/2 Pages) Extech Instruments Corporation. – Pocket Multimeter 4000 Count Autoranging DMM

User’s Guide
Pocket Multimeter
4000 Count Autoranging DMM
Model: DM100
Safety
International Safety Symbols
This symbol, adjacent to another symbol or
terminal, indicates the user must refer to the manual
for further information.
This symbol, adjacent to a terminal, indicates that,
under normal use, hazardous voltages may be
present.
Double insulation
Safety Precautions
1. Improper use of this meter can cause damage, shock, injury or
death. Read and understand this users manual before
operating the meter.
2. Make sure any covers or battery doors are properly closed and
secured.
3. Always disconnect the test leads from any voltage source
before replacing the battery or fuses.
4. Do not exceed the maximum rated input limits.
5. Use great care when making measurements if the voltages are
greater than 25VAC rms or 35VDC. These voltages are
considered a shock hazard.
6. Always discharge capacitors and remove power from the
device under test before performing Capacitance, Diode,
Resistance or Continuity tests.
7. Remove the battery from the meter if the meter is to be stored
for long periods.
Specifications
Electrical Specifications
Function Range
DC Voltage
4.000V, 40.00V,
400.0V,500V
AC Voltage
40-400Hz
4.000V, 40.00V
400.0V, 500V
Resistance
400.0Ω, 4.000kΩ,
40.00kΩ, 400.0kΩ
4.000MΩ
40.00MΩ
Capacitance
40.00nF
400.0nF
4.000µF, 40.00µF,
100.0µF
Frequency
5.000Hz, 50.00Hz,
500.0Hz, 5.000kHz,
50.00kHz, 500.0kHz,
10MHz
Duty Cycle
0.1-99%
Accuracy
±(1.3% rdg + 3d)
±(1.0% rdg + 10d)
±(2.3% rdg + 5d)
±(2.0% rdg + 5d)
±(5.0% rdg + 5d)
±(10.0% rdg + 5d)
±(5.0% rdg + 30d)
±(3.0% rdg + 15d)
±(10.0% rdg + 15d)
±(2.0% rdg + 5d)
Warranty
EXTECH INSTRUMENTS CORPORATION warrants this instrument
to be free of defects in parts and workmanship for one year from date
of shipment (a six month limited warranty applies on sensors and
cables). If it should become necessary to return the instrument for
service during or beyond the warranty period, contact the Customer
Service Department at [phone] ext. 210 for authorization or
visit our website at www.extech.com for contact information. A Return
Authorization (RA) number must be issued before any product is
returned to Extech. The sender is responsible for shipping charges,
freight, insurance and proper packaging to prevent damage in transit.
This warranty does not apply to defects resulting from action of the
user such as misuse, improper wiring, operation outside of
specification, improper maintenance or repair, or unauthorized
modification. Extech specifically disclaims any implied warranties or
merchantability or fitness for a specific purpose and will not be liable
for any direct, indirect, incidental or consequential damages. Extech's
total liability is limited to repair or replacement of the product. The
warranty set forth above is inclusive and no other warranty, whether
written or oral, is expressed or implied.
Copyright © 2004 Extech Instruments Corporation. All rights reserved
including the right of reproduction in whole or in part in any form.
DM100 V1.1 4/04
Description
Meter Description
1. 3 3/4 Digit (4000 count)
2. RELATIVE button
3. SELECT button
1
2
4. DATA HOLD button
3
4
5. Hz/DUTY button
5
6. Function switch
6
7. Plastic case
8. Test leads
7
Max input voltage 500V AC/DC
Input Sensitivity,
10Vrms min. <9.999KHz
(Frequency Ranges) 40Vrms min. >99.99KHz
Diode Test
Test current 1mA max., open circuit voltage
of 1.5V typical
Continuity Check
Audible signal if the resistance is < 60Ω
Display
4000 count 3 ¾ digit LCD
Over range indication LCD displays “OL”
8
Polarity
Minus (-) sign for negative polarity.
Low Battery Indication “BAT” symbol indicates low battery
condition.
Battery
CR2032 3V Lithium
Operating Temperature 32^oF to 104^oF (0^oC to 40^oC)
Storage Temperature 14^oF to 122^oF (-10^oC to 50^oC)
Weight
1.7oz (50g)
Size
4.25x2.2x.5” (108x56x11.5mm)
Standard
IEC1010 CAT II 500V Pollution degree II,
CE Approved