XR16M2550 Datasheet, PDF (33/47 Pages) Exar Corporation – HIGH PERFORMANCE LOW VOLTAGE DUART WITH 16-BYTE FIFO

XR16M2550
REV. 1.0.2
HIGH PERFORMANCE LOW VOLTAGE DUART WITH 16-BYTE FIFO
4.13 Device Revision Register (DREV) - Read Only
This register contains the device revision information. For example, 0x01 means revision A. Prior to reading
this register, DLL and DLM should be set to 0x00 (DLD = 0xXX).
4.14 Enhanced Feature Register (EFR)
Enhanced features are enabled or disabled using this register. Bit 0-3 provide single or dual consecutive
character software flow control selection (see Table 14). When the Xon1 and Xon2 and Xoff1 and Xoff2 modes
are selected, the double 8-bit words are concatenated into two sequential characters. Caution: note that
whenever changing the TX or RX flow control bits, always reset all bits back to logic 0 (disable) before
programming a new setting.
EFR[3:0]: Software Flow Control Select
Single character and dual sequential characters software flow control is supported. Combinations of software
flow control can be selected by programming these bits.
TABLE 14: SOFTWARE FLOW CONTROL FUNCTIONS
EFR BIT-3
CONT-3
0
0
1
0
1
X
X
X
1
0
1
0
EFR BIT-2
CONT-2
0
0
0
1
1
X
X
X
0
1
1
0
EFR BIT-1
CONT-1
0
X
X
X
X
0
1
0
1
1
1
1
EFR BIT-0
CONT-0
TRANSMIT AND RECEIVE SOFTWARE FLOW CONTROL
0
No TX and RX flow control (default and reset)
X
No transmit flow control
X
Transmit Xon1, Xoff1
X
Transmit Xon2, Xoff2
X
Transmit Xon1 and Xon2, Xoff1 and Xoff2
0
No receive flow control
0
Receiver compares Xon1, Xoff1
1
Receiver compares Xon2, Xoff2
1
Transmit Xon1, Xoff1
Receiver compares Xon1 or Xon2, Xoff1 or Xoff2
1
Transmit Xon2, Xoff2
Receiver compares Xon1 or Xon2, Xoff1 or Xoff2
1
Transmit Xon1 and Xon2, Xoff1 and Xoff2,
Receiver compares Xon1 and Xon2, Xoff1 and Xoff2
1
No transmit flow control,
Receiver compares Xon1 and Xon2, Xoff1 and Xoff2
EFR[4]: Enhanced Function Bits Enable
Enhanced function control bit. This bit enables IER bits 4-7, ISR bits 4-5, FCR bits 4-5, MCR bits 5-7, and DLD
to be modified. After modifying any enhanced bits, EFR bit-4 can be set to a logic 0 to latch the new values.
This feature prevents legacy software from altering or overwriting the enhanced functions once set. Normally, it
is recommended to leave it enabled, logic 1.
• Logic 0 = modification disable/latch enhanced features. IER bits 4-7, ISR bits 4-5, FCR bits 4-5, MCR bits 5-
7, and DLD are saved to retain the user settings. After a reset, the IER bits 4-7, ISR bits 4-5, FCR bits 4-5,
MCR bits 5-7, and DLD are set to a logic 0 to be compatible with ST16C550 mode (default).
• Logic 1 = Enables the above-mentioned register bits to be modified by the user.
33