SP6201EM5-L-5-0 Datasheet, PDF (2/17 Pages) Exar Corporation – 100mA/200mA Micropower CMOS LDO Regulators

SP6200 / SP6201
100mA/200mA Micropower CMOS LDO Regulators
ABSOLUTE MAXIMUM RATINGS
OPERATING RATINGS
These are stress ratings only and functional operation of
the device at these ratings or any other above those
indicated in the operation sections of the specifications
below is not implied. Exposure to absolute maximum
rating conditions for extended periods of time may affect
reliability.
Supply Input Voltage (VIN) ............................... -2V to 7V
Output Voltage (VOUT)............................ -0.6 to (VIN +1V)
Enable Input Voltage (VEN)............................... -2V to 7V
Storage Temperature ............................-65°C to +150°C
Power Dissipation ............................... Internally Limited¹
Lead Temperature (Soldering, 5 sec) ..................... 260°C
ELECTRICAL SPECIFICATIONS
Input Voltage Range VIN............................. +2.5V to +6V
Enable Input Voltage (VEN) ................................ 0V to 6V
Junction Temperature Range ....................-40°C to 125°C
Thermal Resistance ......................................................
SOT-23-5 (θJA) .............................................191°C/W
DFN-8 (θJA) ................................................... 59°C/W
Note 1: Maximum power dissipation can be calculated
using the formula: PD = (TJ(max) - TA) / θJA, where
TJ(max) is the junction temperature, TA is the ambient
temperature and θJA is the junction-to-ambient thermal
resistance. θJC is 6°C/W for this package. Exceeding the
maximum allowable power dissipation will result in
excessive die temperature and the regulator will go into
thermal shutdown mode.
Specifications with standard type are for an Operating Junction Temperature of TJ = 25°C only; limits applying over the full
Operating Junction Temperature range are denoted by a “•”. Minimum and Maximum limits are guaranteed through test,
design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25°C, and are provided for
reference purposes only. Unless otherwise indicated, VIN = (VOUT + 1V), VOUT = 5V for Adjustable version, CIN = 1.0µF, COUT =
1.0µF and IL = 100µA, TJ= 25°C.
Parameter
Output Voltage Accuracy, (VO)
Reference Voltage
Output Voltage Temperature
Coefficient² (∆ VO/∆T)
Minimum Supply Voltage
Line Regulation, (∆VO/VIN)
Load Regulation³ (∆VO/VO)
SP6200-1.5V & 1.8 Load Reg.
SP6201-1.5V & 1.8 Load Reg.
Dropout Voltage⁴ (VIN – VO)
(Not applicable to voltage
options below 2.7V)
Shutdown Quiescent Current
(IGND)
Ground Pin Current⁵ (IGND)
Power Supply Rejection Ratio,
(PSRR)
Current Limit, (ICL)
Min.
-2
-3
1.213
100
Typ.
1.250
60
2.50
2.55
2.70
3.00
0.03
0.07
0.14
0.3
0.3
0.2
70
160
320
0.01
28
110
200
78
40
140
Max.
2
3
1.287
2.70
2.80
2.95
3.50
0.2
0.25
0.50
1
1
4
7
120
160
250
300
400
500
1
40
45
200
250
400
500
200
Units
Conditions
%
V
ppm/°C
V
V
V
V
%/V
%
%
%
%
mV
mV
mV
mV
µA
• ^{Variation from specified VOUT}
• Adjustable version only
IL = 100µA
IL = 50mA
IL = 100mA
IC = 200mA
• V_IN = (V_OUT + 1V) to 6V
• I_L = 0.1mA to 100mA, SP6200
• I_L = 0.1mA to 200mA, SP6201
IL = 0.1mA to 100mA, VIN = 2.95V
IL = 0.1mA to 200mA, VIN = 3.5V
• ^{IL = 100µA}
• ^{IL = 50mA}
• ^{IL = 100mA}
• ^{IL = 200mA, SP6201 Only}
• V_EN ≥ 0.4V
µA
• ^{VEN ≥ 2.0V, IL = 100 µA}
µA
VEN ≥ 2.0V, IL = 100 mA, SP6200 only
• ^{(for 1.5 & 1.8, V}IN ^{= 2.95)}
µA
VEN ≥ 2.0V, IL = 200mA, SP6201 Only
• ^{(for 1.5 & 1.8, V}IN ^{= 3.5)}
dB
Frequency = 100Hz, IL = 10mA
Frequency = 400Hz, IL = 10mA
mA
• SP6200
© 2012 Exar Corporation
2/17
Rev. 2.1.0