SP507 Datasheet, PDF (17/28 Pages) Sipex Corporation – +5V, Single Chip WAN Multi-Mode Serial Transceiver

Pin 45 — RL(b) — Remote Loopback; analog
output, non-inverted; sourced from RL.
Pin 47 — RL(a) — Remote Loopback;
analog output inverted; sourced from RL.
Pin 49— LL(b) — Local Loopback; analog
output, non-inverted; sourced from LL.
Pin 51 — LL(a) — Local Loopback; analog
output, inverted; sourced from LL.
Pin 52 — RS(b) — Ready To Send; analog
output, non-inverted; sourced from RTS.
Pin 54 — RS(a) — Ready To Send; analog
output, inverted; sourced from RTS.
Pin 56 — TR(b) — Terminal Ready; analog
output, non-inverted; sourced from DTR.
Pin 58 — TR(a) — Terminal Ready; analog
output, inverted; sourced from DTR.
Pin 66 — CS(a)— Clear To Send; analog
input, inverted; source for CTS.
Pin 67 — CS(b)— Clear To Send; analog
input, non-inverted; source for CTS.
Pin 68 — DM(a)— Data Mode; analog input,
inverted; source for DSR.
Pin 69 — DM(b)— Data Mode; analog input,
non-inverted; source for DSR
Pin 78 — DSR— Data Set Ready; TTL
output; sourced from DM(a) and DM(b) in-
puts.
Pin 80 — CTS— Clear To Send; TTL output;
sourced from CS(a) and CS(b) inputs.
CONTROL REGISTERS
Pin 2 — RTEN — Enables RxC receiver,
active low; TTL input.
Pin 3 — RREN — Enables DCD receiver,
active low; TTL input.
Pin 4 — TMEN — Enables TM receiver,
active high; TTL input.
Pin 5 — LLEN — Enables LL driver, active
low; TTL input.
Pin 6 — TTEN — Enables TxCE driver,
active high; TTL input.
Pin 7 — SCTEN — Enables DTE_ST re-
ceiver; active low; TTL input.
Pin 8 — LATCH — Latch control for decoder
bits (pins 10-12), active low. Logic high input
will make decoder transparent.
Pin 9 — TERM_OFF — Disables receiver
termination networks for RxD, RxC, and
DTE_ST; TTL input.
Pins 10,11, 12 — M2, M1, M0 — Transmitter
and receiver decode register; configures
transmitter and receiver modes; TTL inputs.
Pin 18 — RLEN — Enables RL driver; active
high; TTL input.
Pin 23 — STEN — Enables DTE_ST driver;
active high; TTL input.
POWER SUPPLIES
Pins 25, 33, 41, 48, 55, 62, 73, 74 — V_CC —
+5V input.
Pins 29, 34, 43, 46, 50, 53, 57, 60, 64, 72,
75 — GND — Ground.
Pin 27 — V_DD +10V Charge Pump Capacitor
— Connects from V_DD to V_CC. Suggested
capacitor size is 22µF, 16V.
Pin 32 — V_SS –10V Charge Pump Capacitor
— Connects from ground to V_SS. Suggested
capacitor size is 22µF, 16V.
Pins 26 and 30
Pump Capacitor
—
—
CCo¹⁺nnaencdtsCf¹ro^– m—C₁^C+htoaCrg₁^e–
.
Suggested capacitor size is 22µF, 16V.
Pins 28 and 31
Pump Capacitor
—
—
CCo²⁺nnaencdtsCf²ro^– m—C₂^C+htoaCrg₂^e–
.
Suggested capacitor size is 22µF, 16V.
SP507_100_081208
SP507 Multi–Mode Serial Transceiver
17
© Copyright 2008 Exar Corporation