9171 Datasheet, PDF (5/6 Pages) List of Unclassifed Manufacturers – Single and dual output models with up to 210W output power

Programmable Dual-Range DC Power Supplies
9170 & 9180 series
Specifications
9171
9172
9173
9174
9181
9182
9183
9184
9185
Output Rating
Low Range
High Range
Number of Channels
Max Output Power
Line Regulation
Voltage
Current
Load Regulation¹
Voltage
Current
0-10 V,
0-10 A
0-20 V,
0-5 A
1
100 W
0-35 V,
0-3 A
0-70 V,
0-1.5 A
1
105 W
0-10 V,
0-10 A
0-20 V,
0-5 A
2
200 W
0-35 V,
0-3 A
0-18 V,
0-8 A
0-10 V,
0-20 A
0-70 V,
0-1.5 A
0-36 V,
0-4 A
0-20 V,
0-10 A
2
1
1
210 W
144 W
200 W
≤ 0.01 %+1 mV
≤ 0.01 %+250 uA
≤ 0.01 %+1 mV
≤ 0.01 %+250 uA
0-35 V,
0-6 A
0-70 V,
0-3 A
1
210 W
0-100 V,
0-2 A
0-200 V,
0-1 A
1
200 W
0-400 V,
0-0.5 A
0-600 V,
0-0.35 A
1
210 W
Normal Mode ≤ 0.35 mVrms ≤ 0.5 mVrms / ≤ 0.35 mVrms ≤ 0.5 mVrms /
Voltage
/ ≤ 3 mVpp ≤ 5 mVpp / ≤ 3 mVpp ≤ 5 mVpp
≤ 0.35 mVrms /
≤ 3 mVpp
Ripple and Noise
(20 Hz – 20 MHz) ^{Normal Mode}
Current
≤ 2 mA rms
Common Mode
Current
≤ 1.5 uA rms
Programming /
Readback Resolution
Voltage
Current
1 mV
1 mA
2 mV
0.1 mA
1 mV
1 mA
2 mV
0.1 mA
1 mV
1 mA
≤ 0.5 mVrms ≤ 1.5 mVrms / ≤ 4.5 mVrms /
/≤5 mVpp ≤ 15 mVpp ≤ 45 mVpp
2 mV
0.2 mA
10 mV
0.1 mA
20 mV
0.01 mA
Programming /
Readback Accuracy
±(% output+offset)
Voltage
Current
≤ 0.05 %
+5 mV
≤ 0.1 %
+2 mA
≤ 0.05 %
+10 mV
≤ 0.1 %
+1 mA
≤ 0.05 %
+5 mV
≤ 0.1 %
+2 mA
≤ 0.05 %
+10 mV
≤ 0.1 %
+1 mA
≤ 0.05 %
+5 mV
≤ 0.1 %
+2 mA
≤ 0.1 %
+5 mA
≤ 0.05 %
+10 mV
≤ 0.1 %
+2 mA
≤ 0.05 %
+50 mV
≤ 0.1 %
+1 mA
≤ 0.05 %
+100 mV
≤ 0.1 %
+0.1 mA
Temperature
Coefficient per °C
±(% output+offset)
Voltage
Current
≤ 0.005 %+1 mV
≤ 0.01 %+3 mA
≤ 0.005 %
+10 mV
≤ 0.005 %
+20 mV
Transient Response Time²
Settling Time³
Measurement Time
OVP Accuracy
≤ 50 µs for output to recover to within 15 mV
≤ 0.5 %+0.1 V
≤ 30 ms
≤ 50 ms
≤ 100 µs for ≤ 100 µs for
output to
output to
recover to within recover to within
50 mV
120 mV
≤ 0.5 %+1 V
OCP Accuracy
OVP/OCP Response Time⁴
Rising Time at Full Load / No Load
≤ 8 ms
≤ 10 ms
≤ 8 ms
≤ 10 ms
≤ 0.5 %+0.1 A
≤ 1 ms
≤ 8 ms
≤ 10 ms
≤ 30 ms
≤ 40 ms
Falling Time at Full Load
≤ 8 ms
≤ 10 ms
≤ 8 ms
≤ 10 ms
≤ 8 ms
≤ 10 ms
≤ 30 ms
≤ 40 ms
Falling Time at No Load
Stability (8 hrs)
±(% output+offset)
Voltage
Current
≤ 250 ms
≤ 0.02 %+2 mV
0.1 %+1 mA
≤ 0.02 %
+10 mV
≤ 0.02 %
+20 mV
Notes:
1 With sense terminal connected.
2 Following a change in output current from full load to half load or vice versa.
3 Maximum time required for the output voltage to change from 1% to 99% or vice versa after receiving a VOLTage or VSET command via GPIB or USB interface.
4 Average time for output to start to drop after OVP/OCP condition occurs.
5
www.bkprecision.com