RJ-6S205 Datasheet, PDF (2/4 Pages) List of Unclassifed Manufacturers – SINGLE TURN CERMET TRIMMERS

COPAL ELECTRONICS
RJ-6
CERMET TRIMMERS
˙LIST OF PART NUMBERS
Adjustment
position
Shape of terminal
(Top view)
Form of packaging
Pieces in package
Plastic bag
Top adjustment
2
1
3
RJ-6P
2
1
3
RJ-6W
Side adjustment
(Ë¢Adjustment
direction)
Rear adjustment
2
1
3
3
1
2
31
2
RJ-6S
RJ-6X
A RJ-6F
50 pcs./pack
˙ELECTRICAL CHARACTERISTICS
Nominal resistance range
10 Ω ~ 5 MΩ
Resistance tolerance
± 10 %
Power ratings
0.5 W (70 °C) 0 W (120 °C)
Resistance law
Linear law
Maximum input voltage DC200 V or power rating, whichever is smaller
Maximum wiper current 100 mA or power rating, whichever is smaller
Effective electrical angle
230 ° (1 turn)
End resistance
1 % or 2 Ω, whichever is greater
C.R.V.
1 % or 3 Ω, whichever is greater
Operating temp. range
Temp. coefficient
Insulation resistance
−55 ~ 120 °C
10 Ω, 20Ω, 5 MΩ : ± 250 10^-6/°C maximum
50 Ω ~ 2 MΩ : ± 100 10^-6/°C maximum
1000 MΩ minimum (DC500 V)
Dielectric strength
Net weight
AC900 V, 60 s
Approx. 0.60 g (RJ-6P,W)
Approx. 0.80 g (RJ-6S, X)
Approx. 1.01 g (RJ-6F)
ʪNominal resistance valuesʫ
A 10 Ω A 20 Ω 50 Ω 100 Ω 200 Ω 500 Ω 1 kΩ 2 kΩ 5 kΩ 10 kΩ
20 kΩ A 25 kΩ 50 kΩ 100 kΩ 200 kΩ A250 kΩ 500 kΩ 1 MΩ 2 MΩ A 5 MΩ
Fig. 1
❈ The above part numbers are all available with the respective combination of
<Nominal resistance values> (Fig. 1).
❈ Verify the above part numbers when placing orders.
The products indicated by A mark are manufactured upon receipt of
order basis.
˙MECHANICAL CHARACTERISTICS
Mechanical angle
Operating torque
Stop strength
Rotational life
Terminal to strength
Thrust rotor
Solderability
270 ° (1 turn)
2~ 15 mN·m {20 ~ 153 gf·cm}
50 mN·m {510 gf·cm} minimum
200 cycles
10 Ω ~ 200 Ω [϶R/R ʽ ± (0.5 Ω +3 %)]
500 Ω ~ 5 MΩ [϶R/R ʽ ± (0.5 Ω +2 %)]
10 N {1.02 kgf} minimum
ʢ Tensile strengthʣ
10 N {1.02 kgf} minimum
245 ± 3 °C, 2 ~ 3 s
{ }É¿Reference only
˙ENVIRONMENTAL CHARACTERISTICS
Test item
Test conditions
Specifications
Thermal shock
Humidity
Shock
Vibration
−65 ~ 125 °C (0.5 h),
5 cycles
−10 ~ 65 °C (80 ~ 98 %),
10 cycles, 240 h
981 m/s², 6 ms
6 directions for 3 times each
Amplitude 1.52 mm or
Acceleration 196 m/s²,
10 ~ 2000 Hz, 3 directions, 12 times each
Load life
70 °C, 0.5 W, 1000 h
Low temp. operation
−55 °C, 2 h
High temp. exposure
120 °C, 250 h
[϶R/R ʽ 1 %]
[S.S. ʽ 1 %]
[϶R/R ʽ 1 %]
[϶R/R ʽ 1 %]
[S.S. ʽ 1 %]
[϶R/R ʽ 2 %]
[S.S. ʽ 1 %]
[϶R/R ʽ 1 %]
[S.S. ʽ 2 %]
[϶R/R ʽ 2 %]
[S.S. ʽ 2 %]
Immersion seal
85 °C, 60 s
No leaks (No continuous bubbles)
Flow soldering :
Soldering heat ^{260 ± 3 °C, 5 ~ 6 s, two times maximum}
Manual soldering : 380 ± 10 °C, 3 ~ 4 s
[϶R/R ʽ 1 %]
϶R/RɿChange in total resistance
S.S. É¿Setting stability
˙ Specifications are subject to change without notice. Specifications in this catalog are for reference. The formal specification sheets will be submitted upon request.