OP280V Datasheet, PDF (2/8 Pages) List of Unclassifed Manufacturers – PLCC-2 Pkg Infrared Light Emitting Diode

Infrared Light Emitting Diode
OP180 & OP280 Series
Absolute Maximum Ratings (T_A=25° C unless otherwise noted)
Storage Temperature Range
Operating Temperature Range—OP180, OP280, OP280K, OP280KT, OP280PS
OP280V
Reverse Voltage
OP180, OP280, OP280PS, OP280V
OP280K, OP280KT
Peak Forward Current [ 1µs pulse width, 300 pps] (Except OP280V)
Lead Soldering Temperature [1/16 inch (1.6 mm) from case for 5 seconds with soldering iron]
Power Dissipation
-40^o C to +100^o C
-25^o C to +85^o C
0^o C to +70^o C
5.0 V
4.0 V
1.0 A
260° C⁽¹⁾
130 mW⁽²⁾
Electrical Characteristics (T_A = 25° C unless otherwise noted)
SYMBOL
PARAMETER
Input Diode
EE (APT)
VF
IR
λP
θHP
Radiant Incidence
OP180
OP280
OP280K
OP280KT
OP280PS
OP280V
Forward Voltage
OP180
OP280
OP280K
OP280KT
OP280V
OP280PS
Reverse Current
Wavelength at Peak Emission
OP180
OP280
OP280KT
OP280PS, OP280K
OPOP280V
Emission Angle at Half Power Points
OP180, OP280, OP280K, OP280KT
OP280PS
OP280V
MIN TYP MAX
UNITS
TEST CONDITIONS
0.50
-
0.50
-
0.65
-
0.65
-
0.10
-
1.50
-
-
1.28
-
-
-
1.50
-
1.55
-
1.95
-
1.50
-
-
-
940
-
890
-
850
-
875
-
850
-
-
-
-
-
-
1.60
1.50
1.80
1.80
2.50
1.80
100
-
-
-
-
-
mW/cm²
IF = 20 mA⁽³⁾
IF = 20 mA⁽³⁾
IF = 20 mA⁽³⁾
IF = 20 mA⁽³⁾
IF = 20 mA⁽³⁾
IF = 7 mA⁽³⁾
IF = 20 mA
IF = 20 mA
V
IF = 20 mA
IF = 50 mA
IF = 7 mA
IF = 20 mA
µA
VR= 5.0 V
IF = 20 mA
nm
IF = 7 mA
-
100
-
IF = 20 mA
-
90
-
Degree° IF = 20 mA
-
18
-
IF = 7 mA
Output Rise Time
tr
OP180, OP280K, OP280KT, OP280PS
OP280
OP280V
Output Fall Time
tf
OP180, OP280K, OP280KT, OP280PS
OP280
OP280V
-
-
-
500
700
-
-
-
100
-
500
-
-
700
-
-
-
100
ns
ns
ps
IF(PK)=50 mA, PW=10 µs, and D.C.=10.0%
IF(PK)=5 mA, PW=10 µs, and D.C.=10.0%
(For OP280V)
ns
ns
ps
Notes:
1. Solder time less than 5 seconds at temperature extreme.
2. Derate linearly at 2.17 mW/° C above 25° C.
3. E_E(APT) is a measurement of the apertured radiant incidence upon a sensing area 0.081” (2.06 mm) in diameter, perpendicular to and
centered on the mechanical axis of the lens and 0.590” (14.99 mm) from the measurement surface. E_E(APT) is not necessarily uniform within
the measured area.
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
Issue B 07/2012
Page 2 of 8
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: [phone] or [phone]
FAX: [phone] [e-mail] www.optekinc.com