VLED-40W-CC Datasheet, PDF (1/4 Pages) List of Unclassifed Manufacturers – Dimmable LED Drivers

VLED-40W Series
Dimmable LED Drivers
Constant Current
Plastic Housing
Electrical Specifications
Input Voltage Range:
100-277 Vac Nom. (90-305 V Min/Max)
Frequency:
50/60 Hz Nom. (47-63 Hz Min/Max)
Power Factor:
>0.90 @ full load, 100V through 277V
Inrush Current:
70 Amps max @ 220 Vac, cold start 25ºC
Input AC Current:
0.6 A max 100Vac, 0.3 A max 220Vac
Maximum Power:
42W
THD:
<_ 20% @ full load
Line Regulation:
± 1%
Load Regulation:
± 3%
Leakage Current:
0.75 mA max @ 277Vac 60Hz
Turn-on Delay:
0.6S @ 110Vac, 0.3S @ 220Vac Typical
Output Ripple:
50%, related to the Voltage-Current Curve of the LED
No-load Power Dissipation: 6W
Protection:
Over-Voltage, Over-Temperature (110º) and
Short Circuit Protection with self-recovery
Environmental Specifications
Minimum Starting Temp: -40ºC
Maximum Case Temp. 90°C
Storage Temperature:
-40ºC to +85ºC
Humidity:
5% to 100%
Cooling:
Convection
Sound Rating:
Class A
MTBF:
327,000 Hours @ 120Vac, 80% load and 25ºC ambient
conditions per MIL-HDBK-217F
Lifetime:
116,000 Hours @ 120Vac, 80% load and 60ºC ambient
EMC:
FCC 47CFR Part 15 Class B compliant
Weight:
350 g
Ordering Options:
-D: 0-10V dimmable version comes with an extra three wires +Purple/-Gray/Yellow on
the output side. 0-10V Dimming is compatible with most quality 0-10V wall dimmers
and direct 0-10V analog signal. See page 2 for additional specifications.
• Total Power: 40 Watts
• Input Voltage: 100-277 Vac Nom.
• UL Dry & Damp Location Rated
• IP66
• High Power Factor with Active Correction
• Output Protection & Lightning Protection
• UL8750 and EN61347
Constant Current - Product Specifications
Model Number
Output Current Output Voltage Max. Output
(mA ±5%)
Range (Vdc) Power (W)
VLED40W-120-C0350-XX
350
60-120
42
VLED40W-094-C0450-XX
450
47-94
42
VLED40W-056-C0700-XX
700
28-56
39
VLED40W-038-C1050-XX
1050
20-38
40
VLED40W-032-C1280-XX
1280
17-32
42
VLED40W-030-C1400-XX
1400
15-30
42
VLED40W-024-C1750-XX
1750
12-24
42
Typical
Efficiency
90%
89%
89%
88%
87%
87%
87%
-XX indicates dimming options are available. See options at left. Blank = fixed current output
Class 2: US/Canada US Only
Sign Components Manual
E332160
Note:
LED drivers are designed and intended to operate LED loads only.
Non-LED loading may be outside the specified design limits of our
LED drivers, and therefore cannot be covered by any warranty.
If you desire to use our LED drivers to operate non-LED loads
please contact us to discuss compatibility.
Specifications subject to change without notice.
Rev 9-2-15
Thomas Research Products • 1225 Bowes Rd • Elgin, IL 60123 • T 847-515-3057 • F 847-515-3047 • www.trpssl.com