VLED-150W-HV Datasheet, PDF (1/4 Pages) List of Unclassifed Manufacturers – Switch Mode LED Drivers

VLED-150W-HV Series
347-480V Input, Fixed & Dimmable Output
Switch Mode LED Drivers
Constant Current with Isolation
Aluminum Housing
Electrical Specifications
Input Voltage Range:
347-480 Nom. Vac (312-512 V Min/Max)
Frequency:
50/60 Hz Nom. (47-63 Hz Min/Max)
Power Factor:
>0.90 @ 75-100% load, 347-480V
Inrush Current:
20 Amps max @ 480Vac, cold start 25ºC
Input Current:
0.70A max @ 347Vac, 0.42A max @ 480Vac
Maximum Power:
150W
Line Regulation:
± 1%
Load Regulation:
± 3%
THD:
<_ 20% @ 75-100% load, 347-480V
Leakage Current:
1 mA @ 480VAC, 60Hz
Typical Efficiency
89-91% at 347VAC
Turn-on Delay:
Protection:
1S max
Over-Voltage, Over-Temperature (105°C),
and Short Circuit Protection
Environmental Specifications
Minimum Starting Temp: -40ºC
Storage Temperature:
-40ºC to +85ºC
Humidity:
5% to 100%
Cooling:
Convection
Sound Rating:
Class A
MTBF:
250,000 Hours @ 480VAC input, 80% load and 25ºC
ambient conditions per MIL-HDBK-217F
Lifetime:
145,700 Hours @ 480Vac, 80% load and 45ºC ambient
Weight:
2.87 lbs. (1300g)
Ordering Options:
-D: 0-10V dimmable version comes with an extra three wires Purple/Gray/Blk-Wht on the
output side. Dimming is compatible with most quality 0-10V wall dimmers and direct
0-10V analog signal. See page 3 for additional specifications.
• Total Power: 150 Watts
• Input Voltage: 347-480 Vac Nom.
• UL Dry & Damp Location Rated
• IP67
• High Power Factor
• UL8750, EN61347
Constant Current - Product Specifications
Model Number
Output Current Output Voltage Max. Output Typical
(mA ±5%)
Range (Vdc) Power (W) Efficiency
VLED150W-258-C0580-X-HV
580
129-258
150
91%
VLED150W-214-C0700-X-HV
700
107-214
150
91%
VLED150W-142-C1050-X-HV
1050
71-142
150
90%
VLED150W-107-C1400-X-HV
1400
53-107
150
90%
VLED150W-071-C2100-X-HV
2100
36-71
150
90%
VLED150W-054-C2800-X-HV
2800
27-54
150
90%
VLED150W-043-C3500-X-HV
3500
21-43
150
89%
VLED150W-036-C4200-X-HV
4200
18-36
150
89%
-X indicates dimming options are available. See options at left. Blank = fixed current output
E332160
Note:
LED drivers are designed and intended to operate LED loads only.
Non-LED loading may be outside the specified design limits of our
LED drivers, and therefore cannot be covered by any warranty.
If you desire to use our LED drivers to operate non-LED loads
please contact us to discuss compatibility.
Specifications subject to change without notice.
Rev 8-25-15
Thomas Research Products • 1225 Bowes Rd • Elgin, IL 60123 • T 847-515-3057 • F 847-515-3047 • www.trpssl.com