TRV-150 Datasheet, PDF (1/2 Pages) List of Unclassifed Manufacturers – Switch Mode LED Drivers

150W TRV-150 Series
Switch Mode LED Drivers
Constant Voltage
Aluminum Housing
Electrical Specifications
Input Voltage Range:
100 - 277 Nom. Vac (90 - 305 V Min/Max)
Frequency:
50/60 Hz Nom. (47-63 Hz Min/Max)
Power Factor:
0.90 @ 75-100% load, 100-277V
THD:
<_ 20% @ 75-100% load, 100-277V
Inrush Current:
65 Amps maximum @ 230 Vac, cold start 25ºC
Input Current:
1.75 A max 100Vac, 0.8 A max 220Vac
Maximum Power:
150W
Line Regulation:
± 1%
Load Regulation:
± 2%
Leakage Current:
1 mA 277 Vac 60Hz
Typical Efficiency
92.5%-93.5% at 220Vac
Turn-on Delay:
0.9S typical 110Vac, 0.5S typical 220Vac
Ripple and Noise:
Protection:
2% V_o
Over-Voltage (latch mode), Over-Temperature (110°C),
Over-Current (hiccup mode), Lightning, and
Short Circuit Protection with Self Recovery
Environmental Specifications
Minimum Starting Temp: -35ºC
Maximum Case Temp. 90°C
Storage Temperature:
-40ºC to +85ºC
Humidity:
5% to 100%
Cooling:
Convection
Sound Rating:
Class A
MTBF:
260,000 Hours @ 110Vac input, 80% load and 25ºC
ambient conditions per MIL-HDBK-217F
Lifetime:
Weight:
77,200 Hours @ 220Vac, 80% load and Tc=60ºC
2.2 lbs. (1.0 kg)
• Total Power: 150 Watts
• Input Voltage: 100-277 Vac Nom.
• UL Dry & Damp Location Rated
• IP67
• Ultra-high Efficiency
• High Power Factor
• UL8750
New Surge Protection and HI-POT Testing
Metal Lock Sheet
Nut
Model Number
TRV-150S012ST
TRV-150S020ST
TRV-150S024ST
TRV-150S036ST
TRV-150S048ST
TRV-150S054ST
Output Voltage Output Current Max. Output
(Vdc ±5%)
Range (mA) Power (W)
12
0-12.5
150
20
0-7.50
150
24
0-6.25
150
36
0-4.17
150
48
0-3.13
150
54
0-2.78
150
Typical
Efficiency
92%
92%
93%
93%
93%
93%
HI-POT Test
Normal Application
The new design of this LED driver provides 1.4KV surge protection. To properly
HI-POT test this unit, the surge protection must be disconnected. The screw, nut, and
metal lock sheet on the input side of the driver provide for this. To test, first remove
the nut and lock sheet as shown. After testing, secure the nut and lock sheet to
provide line-to-earth protection.
This HI-POT test feature is available on product manufactured after August 15, 2015.
E332160
Note:
LED drivers are designed and intended to operate LED loads only.
Non-LED loading may be outside the specified design limits of our
LED drivers, and therefore cannot be covered by any warranty.
If you desire to use our LED drivers to operate non-LED loads
please contact us to discuss compatibility.
Specifications subject to change without notice.
Safety and EMC Compliance
UL/CUL
UL8750, Compliance to UL1012, UL935,
CAN/CSA-C22.2 No. 0, CSA-C22.2 No. 107.1-01, CSA-C22.2 No. 250.0
CE
EN 61347-1, EN61347-2-13
EN 55015
Conducted emission Test & Radiated emission Test
EN 61000-3-2 Harmonic current emissions
EN 61000-3-3 Voltage fluctuations & flicker
EN 61000-4-2 Electrostatic Discharge (ESD): 8 kV air discharge, 4 kV contact discharge
EN 61000-4-3 Radio-Frequency Electromagnetic Field Susceptibility Test-RS
EN 61000-4-4 Electrical Fast Transient / Burst-EFT
EN 61000-4-5 Surge Immunity Test: AC Power Line: line to line 4 kV, line to earth 6 kV
EN 61000-4-6 Conducted Radio Frequency Disturbances Test-CS
EN 61000-4-8 Power Frequency Magnetic Field Test
EN 61000-4-11 Voltage Dips
EN 61547
Electromagnetic Immunity Requirements Applies to Lighting Equipment
Rev 8-28-15
Thomas Research Products • 1225 Bowes Rd • Elgin, IL 60123 • T 847-515-3057 • F 847-515-3047 • www.trpssl.com