SMP-12V-BC Datasheet, PDF (1/5 Pages) List of Unclassifed Manufacturers – 2.5mm pitch/Disconnectable Crimp style wire-to-wire connectors

SM CONNECTOR
2.5mm pitch/Disconnectable Crimp style wire-to-wire connectors
The SM series are 2.5mm pitch,
wire-to-wire connectors that perform
reliably in high-density, small current
applications.
• High contact pressure
• Highly reliable housing construction
• Mountable on a variety of panels
• Arm lock mechanism
Specifications –––––––––––––––––––
• Current rating: 3A AC, DC max.
• Voltage rating: 250V AC, DC max.
• Temperature range: -25˚C to +85˚C
(including temperature rise in applying
electrical current)
• Contact resistance: Initial value/ 10m Ω max.
After environmental testing/ 20m Ω max.
• Insulation resistance: 500M Ω min.
• Withstanding voltage: 1,500V AC/minute
• Applicable wire: AWG #28 to #22
0.08 to 0.33mm²
• Applicable panel thickness: 0.5 to 2.0mm
* Compliant with RoHS.
* Refer to "General Instruction and Notice when using
Terminals and Connectors" at the end of this catalog.
* Contact JST for details.
Standards ––––––––––––––––––––––
0 ^{Recognized E60389}
1^{Certified LR20812}
2 ^R50120150
ʢʣ

(2 to 12 circuits)
Ê´

ɹ

(18 circuits)
"
#
 Ê´




"
#
Circuits
2
3
4
5
6
7
8
9
10
11
12
18
Plug housing Model No.
SMP-02V-B(N)C
SMP-03V-B(N)C
SMP-04V-B(N)C
SMP-05V-B(N)C
SMP-06V-B(N)C
SMP-07V-B(N)C
SMP-08V-B(N)C
SMP-09V-B(N)C
SMP-10V-B(N)C
SMP-11V-B(N)C
SMP-12V-B(N)C
SMP-18V-B(N)C
Panel thickness (mm)
0.5ʙ0.9
1.0ʙ1.5
1.5ʙ2.0
Panel hole dimensions (mm) General tolerance
AÊ´0.15




0
B ^ʶ0.1
AÊ´0.15




0
B ^ʶ0.1
AÊ´0.15




0
B ^ʶ0.1
5.7
9.6
5.7
9.8
5.7 10.0
8.2 12.1
8.2 12.3
8.2 12.5
10.7 14.6 10.7 14.8 10.7 15.0
13.2 17.1 13.2 17.3 13.2 17.5
15.7 19.6 15.7 19.8 15.7 20.0
18.2 22.1 18.2 22.3 18.2 22.5
20.7 24.6 20.7 24.8 20.7 25.0
23.2 27.1 23.2 27.3 23.2 27.5
25.7 29.6 25.7 29.8 25.7 30.0
28.2 32.1 28.2 32.3 28.2 32.5
30.7 34.6 30.7 34.8 30.7 35.0
23.2 27.2 23.2 27.4 23.2 27.6
Note: 1. Punch holes in the panel according to the sketch and table shown above. Burrs must be removed.
2. The strength of the panel must be considered when punching two or more holes.
3. The connector must be inserted from the same side as the hole is punched.
1