|
SGL04G72B1BQ2SA-BBRT Datasheet, PDF (1/18 Pages) List of Unclassifed Manufacturers – 4096MB DDR3 – SDRAM unbuffered ECC Mini-UDIMM | |||
|
Data Sheet
Rev.1.0 18.02.2014
4096MB DDR3 â SDRAM unbuffered ECC Mini-UDIMM
244 Pin ECC Mini-UDIMM
SGL04G72B1BQ2SA-xxRT
4GB in FBGA Technology
RoHS compliant
Options:
ï§ Data Rate / Latency
DDR3 1066 MT/s CL7
DDR3 1333 MT/s CL9
DDR3 1066 MT/s CL7
ï§ Module density
4GByte with 18 dies and 2 ranks
ï§ Standard Grade (TA)
(TC)
Marking
-BB
-CC
-BB
0°C to 70°C
0°C to 85°C
*) The refresh rate has to be doubled when 85°C<TC<95°C
Environmental Requirements:
ï§ Operating temperature (ambient)
Standard Grade
0°C to 70°C
-40°C to 85°C
ï§ Operating Humidity
10% to 90% relative humidity, noncondensing
ï§ Operating Pressure
105 to 69 kPa (up to 10000 ft.)
ï§ Storage Temperature
-55°C to 100°C
ï§ Storage Humidity
5% to 95% relative humidity, noncondensing
ï§ Storage Pressure
1682 PSI (up to 5000 ft.) at 50°C
Features:
ï§ 244-pin 72-bit DDR3 ECC Mini-UDIMM module
ï§ Module organization: dual rank 512M x 72
ï§ VDD = 1.5V ±0.075V, VDDQ 1.5V ±0.075V
ï§ 1.5V I/O ( SSTL_15 compatible)
ï§ Fly-by-bus with termination for C/A & CLK bus
ï§ On-board I2C temperature sensor with integrated serial
presence-detect (SPD) EEPROM
ï§ Gold-contact pad
ï§ This module is fully pin and functional compatible to the
JEDEC PC3-10600 DDR3 SDRAM Mini-UDIMM design spec.
and JEDEC- Standard MO-244 R/C B. (see www.jedec.org)
ï§ The pcb and all components are manufactured according to
the RoHS compliance specification
[EU Directive 2002/95/EC Restriction of Hazardous
Substances (RoHS)]
DDR3 - SDRAM component Samsung K4B2G0846Q
ï§ 256Mx8 DDR3 SDRAM in PG-TFBGA-78 package
ï§ 8-bit prefetch architecture
ï§ Programmable CAS Latency, CAS Write Latency, Additive
Latency, Burst Length and Burst Type.
ï§ On-Die-Termination (ODT) and Dynamic ODT for improved
signal integrity.
ï§ Refresh, Self Refresh and Power Down Modes.
ï§ ZQ Calibration for output driver and ODT.
ï§ System Level Timing Calibration Support via Write Leveling
and Multi Purpose Register (MPR) Read Pattern.
Figure: mechanical dimensions1
82.00
Swissbit AG
Industriestrasse 4
CH â 9552 Bronschhofen
Fon: +41 (0) 71 913 03 03
Fax: +41 (0) 71 913 03 15
1if no tolerances specified ± 0.15mm
www.swissbit.com
eMail: info@swissbit.com
Page 1
of 18
|
▷ |