SDS-8-014 Datasheet, PDF (1/1 Pages) List of Unclassifed Manufacturers – SpectraDIL - 014 style SDS, SDC, SDD ranges

SpectraDIL - 014 style
SDS, SDC, SDD ranges
This series offers standard programme setting
switches to suit applications where ‘end stacking’
up to any number of switches without missing a
pitch is required.
Large numerals and actuators plus EIA colour
coded sliders with open access to them.
Base sealed for flow soldering. If immersion
washing, use 023 series.
1µm hard gold plated wiping contact gives high
reliability in low level circuits.
If you have a volume requirement for a
product variant not shown on this sheet
please contact us.
SpectraDIL ON/OFF s.p.s.t
Number of
s.p.s.t
1
2
4
6
8
10
Part Nos
SDS-plus
suffix
1-014
2-014
4-014
6-014
8-014
10-014
Length
mm
max
3.1
5.0
10.1
15.0
20.1
25.2
SDS 014 series
SpectraDIL CHANGEOVER s.p.d.t.
Number of
s.p.d.t
1
2
3
4
5
Part Nos
SDC-plus
suffix
1-014
2-014
3-014
4-014
5-014
Length
mm
max
5.0
10.1
15.0
20.1
25.2
SDC 014 series
SpectraDIL GANGED ON/OFF d.p.s.t
Number of
d.p.s.t
1
2
3
4
5
Part Nos
SDD-plus
suffix
1-014
2-014
3-014
4-014
5-014
Length
mm
max
5.0
10.1
15.0
20.1
25.2
SDD 014 series
Principal Electrical and Performance Data
at 20˚C 70% R.H.
Contact Ratings: Non Switching: 100Vac, 5A
Switching: 1µV to 100V, 1µA to 1A up to 10VA.
Initial Contact Resistance: (at 10mV, 10mA max.)
Typical: 10mΩ. Max. 20mΩ.
Insulation Resistance: (at 500Vdc min.) 10,000MΩ.
Life: For the first 1000 closures the standard deviation of the
change in resistance from the mean is usually less than 1mΩ.
Mechanical wear out of the sliding actuator is usually observed
after 10,000 operations.
Dielectric Strength: 1 minute: 500Vrms 50Hz.
Capacitance Between Open Contacts: < 1pf at 1KHz.
Temperature: Operating range for continuous electrical use
and manual operation is restricted to -55˚C to +100˚C for
standard products.
Humidity: BS 2011 Test Ca: 56 days.
Bump: BS 2011 Test Eb: No contact interruptions > 1µs during
4000 bumps at 390m/s² (40g).
Acceleration: BS 2011 Test Ga: No contact interruptions > 1µs
during test at 980 m/s² (100g).
Vibration: BS 2011 Test Fc: 10 to 2000Hz. No contact
interruptions > 1µs during test at 147m/s² (15g) or 1.0mm
displacement amplitude.
Shock: BS 2011 Test Ea: 980 m/s² (100g). No contact
interruptions > 1µs during test.
Soldering: solderability: < 2 seconds to wet at 235˚C as per
IEC 68 and BS 2011 Test T, solder bath method.
Resistance to soldering heat as per IEC 68 and BS 2011 10
seconds satisfactory at 260˚C when mounted on 1.5mm PCB.
Please note: BS 2011 is now superseded by BS EN 60068.