SCS-6-023 Datasheet, PDF (1/1 Pages) List of Unclassifed Manufacturers – Principal Electrical and Performance Data

Using a third common contact pin halves the
PCB area to maximise code setting on
crowded PCB's. They are also used widely for
two state, pull up / pull down resistor setting.
Large numerals and EIA colour coded
sliders.
Base and tape seal for flow soldering and
solvent / aqueous washing.
1µm hard gold plated wiping contact gives
high reliability.
If you have a volume requirement for a
product variant not shown, please contact us.
Spectra C CHANGEOVER TRIPLE IN LINE s.p.d.t
SCS 023 series
Number of
s.p.d.t
1
2
4
6
8
10
Part Nos
SCS-plus
suffix
1-023
2-023
4-023
6-023
8-023
10-023
Length
mm
max
4.0
6.7
11.8
16.8
21.9
27.0
10.5 max
9 (max)
0.40 x 3.0- 5.0
2.54
0.55
length
2.54 pitch
7.62
Spectra C GANGED CHANGEOVER TRIPLE IN LINE d.p.d.t
SCS G-023 series
Number of
d.p.d.t
1
2
3
4
5
Part Nos
SCS-plus
suffix
1G2-023
2G2-023
3G2-023
4G2-023
5G2-023
Length
mm
max
4.0
6.7
11.8
16.8
21.9
10.5 max
9 (max)
0.40 x 3.0- 5.0
2.54
0.55
length
2.54 pitch
7.62
This leaflet is believed to contain the best information available at the time of printing,
but is subject to change without notice. Performance figures, where quoted, are
actually estimates based on our experience or that of our customers or statutory
authorities. In common with all components reliability varies with many factors, and
users are invited to contact us in appropriate cases so that where relevant information
is available it may be considered by the user. All supplies are subject to the Company's
standard conditions of sale which are available on request.
Principal Electrical and Performance Data
at 20˚C 70% R.H.
Contact Ratings: Non Switching: 100Vac, 5A Switching: 1 µV to
100V, 1µA to 1A up to 10VA.
Initial Contact Resistance: (at l0mV, l0mA max.) Typical: 10m .
Max. 20m .
Insulation Resistance: (at 500Vdc min.) l0,000M .
Life: For the first 1000 closures the standard deviation of the
change in resistance from the mean is usually less than 1 m .
Mechanical wear out of the sliding actuator is usually observed
after 10,000 operations.
Dielectric Strength: 1 minute: 500Vrms 50Hz.
Capacitance Between Open Contacts: < 1 pf at 1 KHz.
Temperature: operating range for continuous electrical use and
manual operation is restricted to -55˚C to +100˚C for standard
products.
Humidity: BS 2011 Test Ca: 56 days.
Bump: BS 2011 Test Eb: No contact interruptions > 1µs during
4000 bumps at 390m/s² (40g).
Acceleration: BS 2011 Test Ga: No contact interruptions > 1µs
during test at 980 m/s² (100g).
Vibration: BS 2011 Test Fc: 10 to 2000Hz. No contact
interruptions > 1 µs during test at 147 m/s² (15g) or l.Omm
displacement amplitude.
Shock: BS 2011 Test Ea: 980 m/s² (100g). No contact
interruptions > 1 µs during test.
Soldering: solderability: < 2 seconds to wet at 235˚C as per IEC
68 and BS 2011 Test T. solder bath method.
Resistance to soldering heat as per IEC 68 and BS 2011 10
seconds satisfactory at 260˚C when mounted on l.5mm PCB.
Please note: BS 2011 is now superseded by BS EN 60068.
Luton Road, Dunstable, Bedfordshire, LU5 4LJ, UK.
Tel: [phone] Fax: [phone]
Email: [e-mail] Web: http://www.erg.co.uk