PS-65 Datasheet, PDF (1/2 Pages) List of Unclassifed Manufacturers – SWITCHING POWER SUPPLY

MEAN WELL
SWITCHING POWER SUPPLY
ISO-9001 CERTIFIED MANUFACTURER
PS-65
SERIES
.LOW COST, HIGH RELIABILITY
.COMPACT SIZE, LIGHT WEIGHT
.105ºC OUTPUT CAPACITOR
.100% FULL LOAD BURN-IN TEST
.INTERNATIONAL AC INPUT RANGE
.BUILT IN EMI FILTER, LOW RIPPLE NOISE
.HIGH EFFICIENCY, LOW WORKING TEMPERATURE
.SOFT-START CIRCUIT, LIMITING AC SURGE CURRENT
.SHORT CIRCUIT, OVERLOAD, OVER VOLTAGE PROTECTED
SPECIFICATION
MODEL
PS-65-3.3 PS-65-5 PS-65-7.5 PS-65-12
PS-65-
13.5
PS-65-15 PS-65-24 PS-65-27 PS-65-48
DC OUTPUT VOLTAGE
OUTPUT V. TOLERANCE
OUTPUT RATED CURRENT
OUTPUT MIN. CURRENT
OUTPUT MAX. CURRENT
RIPPLE & NOISE p-p
LINE REGULATION
LOAD REGULATION
RATED OUTPUT POWER
MAXIMUM OUTPUT POWER
EFFICIENCY
DC VOLTAGE ADJ.
INPUT VOLTAGE RANGE
AC CURRENT
INRUSH CURRENT
LEAKAGE CURRENT
OVERLOAD PROTECTION
OVER VOLTAGE PROTECTION
TEMP. COEFFICIENT
SETUP, RISE, HOLD UP TIME
VIBRATION
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
WORKING TEMP., HUMIDITY
STORAGE TEMP., HUMIDITY
DIMENSION
WEIGHT
SAFETY STANDARDS
EMC STANDARDS
3.3V
5V
7.5V
12V
13.5V
15V
24V
27V
48V
±3%
±3%
±3%
±2%
±2%
±2%
±2%
±2%
±2%
12A
12A
8A
5.2A
4.7A
4.2A
2.7A
2.4A
1.35A
0A
0A
0A
0A
0A
0A
0A
0A
0A
15.2A
13.8A
9.6A
6A
5.4A
4.8A
3A
2.7A
1.5A
80mV 100mV 100mV 100mV 100mV 100mV 100mV 100mV 100mV
±1%
±1%
±1%
±1%
±1%
±1%
±1%
±1%
±1%
±3%
±3%
±3%
±2%
±2%
±2%
±2%
±2%
±2%
39.6W 60W
60W 62.4W 63.5W 63W 64.8W 64.8W 64.8W
RATED OUTPUT POWER FOR CONVECTION; 72W (+3.3V:50W;+5V:69W) WITH 18 CFM MIN. FORCED
AIR
69%
76%
79%
79%
79%
79%
80%
80%
80%
+10,-5%
90~264VAC 47~440Hz ; 120~370VDC
1.5A/115V 0.9A/230V
COLD START 20A/115V 40A/230V
<0.5mA/240VAC
73~105W (3.3V:51~75W)(5V:70~105W) TYPE:PULSING HICCUP SHUTDOWN RESET:AUTO
RECOVERY
115%~135%
±0.04% / ºC (0~50ºC)
800ms, 20ms, 20ms
10~500Hz, 2G 10min./1cycle, PERIOD FOR 60min. EACH AXES
I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:500VDC / 100M Ohms
-10ºC~+60ºC(REFER TO OUTPUT DERATING CURVE), 20%~90% RH
-20ºC~+85ºC, 10%~95% RH
127*76.2*42mm (L*W*H) PCB ONLY
0.28Kgs
UL1950, TUV EN60950 APPROVED
CISPR22 (EN55022), IEC1000-4-2,3,4,5 IEC1000-3-2,3 VERIFICATION
NOTE :
1.ALL PARAMETERS ARE SPECIFIED AT 230VAC INPUT, RATED LOAD, 25ºC 70% RH. AMBIENT.
2.TOLERANCE GINCLUDE SET UP TOLERANCE, LINE REGULATION, LOAD REGULATION.
3.RIPPLE & NOISE ARE MEASURED AT 20MHz BY USING A 12" TWISTED PAIR TERMINATED WITH A 0.1uF & 47uF CAPACITOR.
4.LINE REGULATION IS MEASURED FROM LOW LINE TO HIGH LINE AT RATED LOAD.
5.OUTPUT PROVIDE UP TO MAXIMUM CURRENT, BUT RELATED TO MAXIMUM OUTPUT POWER.
6.MOUNTING HOLES M1 AND M2 SHOULD BE GROUNDED FOR EMI PURPOSES.
2002-04-29