PCI-7442 Datasheet, PDF (1/2 Pages) List of Unclassifed Manufacturers – High-density 128-CH Isolated DIO/DI/DO Cards

PCI-7442/7443/7444
High-density 128-CH Isolated DIO/DI/DO Cards
PCI-7442
Introduction
Responding to the industry’s need for high-density digital input/output modules, the ADLINK PCI-744X DIO
card series delivers up to 128 opto-isolated channels for a wide range of demanding PCI-based applications.
The PCI-744X card series comes with 64 (PCI-7442) or 128 (PCI-7443) opto-isolated digital inputs and 64 (PCI-7442)
or 128 (PCI-7444) opto-isolated digital outputs. With a 1250 VRMS (excluding cables) channel-to-system isolation protection,
these cards are shielded from damage caused by accidental contact with external voltage while promoting simple ground
connections. All input channels are identical non-polarity with each line isolated and suited to collect digital inputs even
at high-noise environments. Featuring a Change-of-State (COS) interrupt function, the PCI-7442/PCI-7443 instantly
generates an interrupt request to the PCI controller when it detects a sharp change in the logical state of any of its digital
inputs.
For easy identification in systems with multiple DIO cards installed, the cards are also equipped with a board ID design
that enables fast and convenient card detection and troubleshooting.
PCI-7443
PCI-7444
Features
■ Supports universal 32-bit 3.3 V and 5 V PCI bus, plug-and-play
■ High-density, opto-isolated digital input and/or digital output
• PCI-7442: 64-CH digital input and 64-CH digital output
• PCI-7443: 128-CH digital input
• PCI-7444: 128-CH digital output
■ 1250 VRMS isolation voltage
■ Programmable Change-of-State (COS) detection for all
digital input channels
■ Voltage protection of up to 28 V for isolated input
■ Dry contact input (PCI-7442 only)
■ Up to 300 mA high-output driving capability for all output
channels
■ 250 mA sink current on isolated output channels
■ Digital output status read back function
■ Digital output value retained after hot system reset
■ Programmable power-up DO initial status
■ Programmable safety DO status functions when
WDT interruption occurs
■ Watchdog timer counter prevents system crashes
(PCI-7442/PCI-7444 only)
■ 32-CH programmable TTL I/O function
■ Board ID feature
■ Operating Systems
• Windows 7/Vista/XP/2000/2003 Server
• Linux
■ Recommended Software
• AD-Logger
• VB.NET/VC.NET/VB/VC++/BCB/Delphi
• DAQBench
■ Driver Support
• DAQPilot for LabVIEW™
• DAQ-MTLB for MATLAB^®
• PCIS-DASK for Windows
• PCIS-DASK/X for Linux
Specifications
Isolated Digital Input
■ Number of channels
• 64 (PCI-7442)
• 128 (PCI-7443)
■ Maximum input range: 28 V, non-polarity
■ Digital logic levels: 0 V to 28 V, non-polarity
• Input high voltage: 5 V to 28 V
• Input low voltage: 0 V to 1.5 V
■ Input resistance: 4.7 kΩ @ 0.5 W
■ ESD protection CKT switch (forward)
■ Isolation voltage: 1250 VRMS channel-to-system
■ Interrupt sources: 64/128-channel Change-of-State
(COS)
■ Data transfer: programmed I/O
Isolated Digital Output
■ Number of channels:
• 64 (PCI-7442)
• 128 (PCI-7444)
■ Output type: open drain Power MOSFET driver
■ Output range: 5 V to 40 V
■ _{Sink current: 250 mA for all channel @ 100% duty}
(300 mA max.)
■ Isolation voltage: 1250 VRMS channel-to-system
■ Data transfer: programmed I/O
Isolation +5 V Power Supply (PCI-7442/7444 only)
■ Output Voltage: +5 V
■ Output Current: 100 mA max. (@ 40˚C)
Safety Functions (PCI-7442/7444 only)
■ Programmable power-up DO status
■ Watchdog timer
• Base clock available: 10 MHz, fixed
• Counter width: 32-bit
General Specifications
■ I/O connector: 68-pin Dual port VHDCI female
■ Operating temperature: 0˚C to 60˚C
■ Storage temperature: -20˚C to 80˚C
■ Relative humidity: 5% to 95%, non-condensing
■ Power requirements
Device
+5 V
PCI-7442
800 mA typical
PCI-7443
550 mA typical
PCI-7444
800 mA typical
■ Dimension: 175 mm x 107 mm
2-49 _{www.adlinktech.com}
Terminal Boards & Cables
■ DIN-68S-01
Terminal Board with One 68-pin SCSI-II Connector
and DIN-Rail Mounting (Cables are not included.)
■ ACL-10568D
Dual-68-Pin Head to Two 68-Pin SCSI-VHDCI Cable
■ ACL-10568F
68-Pin SCSI-VHDCI Flat Cable
* For more information on mating cables, please refer to P2-61/62.
Ordering Information
■ PCI-7442
64-CH Isolated DI and 64-CH Isolated DO card
■ PCI-7443
128-CH Isolated DI card
■ PCI-7444
128-CH Isolated DO card